Size of Wrenches/Sockets Needed to Install Curt Weight Distribution System # C17062

Question

Question:

What size sockets are needed for hitch installation.

asked by: Frank W

0

Expert Reply:

I looked up the bolt and nut sizes that come with the Curt weight distribution system part # C17062 and the sizes you need are 3/4", 1-1/8", 1-7/8", and 9/16".

expert reply by: Jameson C

0

Answer 1

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Answer 2

The Curt hitch ball #C40007 has a 1" diameter shank. Curt Hitch balls with a 1" shank will use a 1-1/2" wrench for the nut. You would also want to use a 2" wrench for the flats on the base of the ball. We offer the 6-point hex…

view full answer...

Answer 3

Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…

view full answer...

Answer 4

The handle is actually the on/off switch for the unit and the bolt under the handle is the tension adjustment bolt. You will need to turn the On/Off handle clockwise (tighter) until the handle will stay firmly in place parallel with the main body of…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Size of Wrenches/Sockets Needed to Install Curt Weight Distribution System # C17062

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching