Wire Gauge Recommended for Installing Lippert LC298707 High Speed Electric Trailer Stabilizer Jack

Question

Question:

what size wire from battery to the motor of the jack.

asked by: Charles P

0

Expert Reply:

Because the power leg is protected by a 20 amp circuit breaker, it's recommended that 12 gauge wire be used. I've provided a wiring diagram of the # LC298707 for you. You can see an install video by clicking the provided link.

expert reply by: Mike L

0

click to enlarge

Answer 1

You will want to use a minimum of 10 gauge wire like #10-1-1 from the battery to the motor on the Lippert High-Speed Power Stabilizer Jack #LC298707. I do not recommend running a front and rear stabilizer to the same power wire. Each wire uses a…

view full answer...

Answer 2

Hey Bruce, while the Lippert stabilizer jack part #LC298707 wasn't designed to have a second switch setup there is a way with an additional switch part #LC387874. You would have to run each wire of this switch and tee it into the wiring on the…

view full answer...

Answer 3

I attached a picture that shows the install instructions for the Lippert Components High-Speed Power Stabilizer Jack #LC298707 that you referenced and in it you'll notice a set distance isn't specified for where it has to install on the…

view full answer...

Answer 4

There will be 4 wires coming from the Lippert Replacement Electric Jack Switch #LC387874 that you are looking at. The blue wire from the switch will go to a 6 amp breaker like #LC134181 that is installed between the switch and jack motor. This will…

view full answer...

Answer 5

I was unable to find your order number but I assume you have the Replacement Electric Jack Switch with Harness #LC387874 for your Lippert Components High-Speed Power Stabilizer Jack #LC298707 as this jack will have black and red wires that the switch…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Wire Gauge Recommended for Installing Lippert LC298707 High Speed Electric Trailer Stabilizer Jack

Featured Help Information

Miscellaneous Media

Continue Researching