Availability of Curt Ball Mount # C45070 with Ball

Question

Question:

can I get a C45070 with a ball installed?

asked by: Tom M

0

Expert Reply:

For the Curt Ball Mount (4" Rise and 6" Drop) # C45070 that comes with a hitch ball you can use part # C45065 for a 2-5/16" ball or # C45064 for a 2" ball.

Both options feature the same 7,500 pound towing weight capacity. Just keep in mind that the hitch ball does come pre-torqued from the factory with the unit in the drop position. It will require a bit of force to remove the ball so that you can flip the mount but you can certainly do this if needed.

Otherwise you can simply order the Curt Ball Mount # C45070 you referenced with separate hitch ball such as the 2" # 63845 or the 2-5/16" # 63847.

expert reply by: Chris R

0

Answer 1

The easiest to install trailer hitch for your 2020 Toyota Sienna is the etrailer part #e98837 which has the shortest install time listed. I attached an install video for this for you to check out as well. Then for trailer wiring the easiest solution…

view full answer...

Answer 2

Hey Greg. Instructions for a etrailer Hitch like item #e98837, that fits your 2020 Toyota Sienna are included with the hitch. I have also linked them below along with another installation video. This may have been the one you saw on Youtube but if…

view full answer...

Answer 3

The main differentiation between the available Class III hitches is how they'll appear once installed. The etrailer brand #e98837 and the Draw-Tite #75237 will have the entire hitch visible under the rear bumper. In contrast, the Draw-Tite #76112…

view full answer...

Answer 4

Hey Daniel thanks for all the questions! One of them is going to be pretty easy but also disappointing, every hitch for your 2019 Toyota Sienna is going to require the panel to be removed, trimmed, then reinstalled. This is actually not as hard to do…

view full answer...

Answer 5

I can absolutely help with choosing a trailer hitch for your 2020 Toyota Sienna that will give you the best ground clearance. There are quite a few hitch options available for your vehicle, but the models that will sit highest off the ground when…

view full answer...

Answer 6

I agree that 6" of drop will likely be good for your truck with a 6" lift, but to verify you can take some measurements as seen in the attached photo. The etrailer Ball Mount #e87DR and the Curt #C45064 both have the same specs of 6"…

view full answer...

Answer 7

Thanks for getting me the coupler and hitch height of your setup. Based on that you'd need a 6 inch drop ball mount. So for a 2 inch ball mount that has the correct amount of drop you'd want the #C45064 which comes with a 2 inch hitch ball…

view full answer...

Answer 8

The distance from the center of the hitch pin hole to the anti-rattle device on the Solid Tow #DTSTBM6600 is right at 2", so it's not going to work if you've got only 1-1/2"; this also does not come with a 1-7/8" hitch ball.…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Availability of Curt Ball Mount # C45070 with Ball

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching