How To Lift A Big Tex 35SA Single Axle Trailer

Question

Question:

Will this fit a big Tex 35SA?

asked by: Tony S

0

Expert Reply:

According to my research, the Big Tex 35SA Trailer comes with a Dexter 3,500 Lb EZ-Lube Axle. Therefore, in order to lift your trailer you can use the Dexter Trailer Springs Over-Under Conversion Kit part # K71-384-00 which will raise the trailer equal to the axle diameter and leaf spring stack height. The Torflex Lift Kit part # K71-707-01 will not work because it is for a torsion axle which you don't have.

expert reply by: Conner L

0

Answer 1

Hello Monte, thanks for reaching out. Both of the springs you mentioned, the etrailer #e54SR and Dexter #DX23CR are springs for a 3,500 lb axle. The difference is the brand and the length. The #e54SR is our etrailer brand and is 25-1/8" long eye…

view full answer...

Answer 2

I am sure we have a set that will work but there's no database that shows me what part numbers your springs are. Big Tex doesn't list this information online either. What I need you to do is jack up one side of your trailer and get the weight…

view full answer...

Answer 3

The correct Dexter Trailer Springs Over-Under Conversion Kit for a Big Tex 35ES Single Axle Utility Trailer with Dexter 3,500 Lb Trailer Axle is part #K71-384-00.

view full answer...

Answer 4

In order to locate correct leaf spring replacements for your Big Tex trailer, you will need to take a quick measurement on your existing springs, from the center of the spring eye to the center of the other spring eye. You will want to take this…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

How To Lift A Big Tex 35SA Single Axle Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching