Quantity of Brackets Included with CargoSmart Folding Track Brackets

Question

Question:

Is the pricing for one bracket or a pair of brackets

asked by: Eric R

0

Expert Reply:

The CargoSmart folding track brackets, part # 3481744, includes two brackets. So the price you see on the product page is for the pair.

expert reply by: Charles S

0

Answer 1

The CargoSmart Folding Workbench #3481744 will sit approximately 3-3/4 to 4" out from the CargoSmart X-track mount #3481770. The braces on the CargoSmart Folding Workbench are 2-1/2" tall and the bracket that mounts in the X track is sits…

view full answer...

Answer 2

Your board can be no more than approximately 1-1/4" thick if you'd like to completely fold up the folding workbench you asked about: - CargoSmart Folding Workbench Brackets for E-Track or X-Track - 26" to 40" Tall #3481744 The…

view full answer...

Answer 3

The legs for the CargoSmart Folding Workbench Brackets #3481744 will sit 22-21/2" away from the wall when in the deployed position, and then the brackets are 2-1/2" tall so they will stick out that far from the wall. My contact at…

view full answer...

Answer 4

Hey Mark, welcome back! I don't see why you wouldn't be able to turn the CargoSmart Folding Workbench Brackets #3481744 into a bed. You will have a little extra hanging off the end since the brackets are only 24" long. The weight…

view full answer...

Answer 5

If you want the table to span the width of your van then the best option would be to use a few of the CargoSmart Board Holders part #348892 and then build a table on these using 2x4's and plywood. If you only want the table to go on one side then…

view full answer...

Answer 6

The CargoSmart Folding Workbench Brackets for E-Track or X-Track, #3481744 lets you create a fold-out workbench or seat and mounts to X-track and E-track rails. I suggest using something such as the CargoSmart Horizontal or Vertical X-Track, #3486500…

view full answer...

Answer 7

I grabbed one of the CargoSmart Folding Workbench Brackets #3481744 and got the following measurement for you. With the upright in the tallest position and the threaded insert pushed all the way in, I got a measurement of 40" from the ground to…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Quantity of Brackets Included with CargoSmart Folding Track Brackets

Product Page this Question was Asked From

Continue Researching