Tools Needed to Install Roadmaster Rear Anti-Sway Bar # RM-1139-149

Question

Question:

Please provide a list of tools socket sizes needed to install this RM-1139-149 and the U-Bolt Kit for Roadmaster Anti-Sway Bars - RM-590050-10.

asked by: Bruce E

0

Expert Reply:

The installation manual for the Roadmaster Rear Anti-Sway Bar # RM-1139-149 along with the Extended U-Bolt Kit # RM-590050-10 simply calls for a torque wrench and "general hand tools". When we installed this kit on the 2017 Ford F-53 we used a 13/16 inch socket, a 5/16 inch socket, a 15/16 inch wrench/socket, an 18mm wrench/socket, and a 16mm socket.

I have attached this installation video below that you can also check out.

expert reply by: Chris R

0

Answer 1

The Roadmaster Rear Anti-Sway Bar part #RM-1259-109 is a bolt-on component that does not require the rear wheels to be removed. Please note the linked installation instructions for you to review.

view full answer...

Answer 2

The correct rear anti-sway bar for the 2011 Ford F-53 motorhome chassis V10 rated for 22,000 pounds is #RM-1139-149. Check to ensure there is enough factory u-bolt available to accommodate the factory nut, washer and 1/2" plate. If the u-bolts…

view full answer...

Answer 3

Hello Mark, Per the tech at Lippert you are going to want to use AW-32 Hydraulic Fluid, and not an automatic transmission fluid.

view full answer...

Answer 4

We typically do not publish torque numbers because manufacturers have been known to substitute hardware of different hardnesses from time to time but they do a great job of keeping the installation instructions updated to reflect any changes.…

view full answer...

Answer 5

Hey Booker, thanks for reaching out! I see you purchased the Left #RVS-775L and Right #RVS-775R Rear View Safety replacement side cameras. These will work as long as your monitor uses the RGA connectors - I'm guessing that's what you have on…

view full answer...

Answer 6

Hey Ronald, it sounds like you are looking for something like the Roadmaster Dual Hitch Adapter part #RM83SR which can do a 4 inch drop and then has a higher hitch opening that you could use for your bike rack. What tow bar are you using?

view full answer...

Answer 7

Hey Darrell, thanks for reaching out! You're going to need the Roadmaster Reflex Steering Stabilizer #RM62VR for your 2025 Ford F-53 chassis. What Class A do you have?

view full answer...

Answer 8

You're already on the right track with everything you looked at. Your 2018 Thor ACE 30.3 has a GVWR of 18,000 lbs so I recommend the following: -Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets for Class A Motorhomes #RM33RR…

view full answer...

Answer 9

Hey Henry, thanks for the pics! The RV Designer GripFit+ Motorhome Seat Cover item #RD27SR are universal so they should fit but let me get you some measurements so you can confirm. The RV Designer item #RD27SR fits seat backs measuring…

view full answer...

Answer 10

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 11

Hey Don, thanks for reaching out. Yeah, the driver’s side on those F53 chassis can get tight, you’ve usually got brake lines, wiring, or a bracket sitting right where you want that Timbren to live. You’re doing the right thing paying attention to it,…

view full answer...

Tools Needed to Install Roadmaster Rear Anti-Sway Bar # RM-1139-149

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching