Mounting Hole Spacing of Ultimate Tuf Combo License Plate Frame CR62510

Question

Question:

What is the distance in inches between the mounting holes on this product? I have a 2018 Ram 1500 Crew Cab.

asked by: Torres

0

Expert Reply:

Mounting hole spacing for the Ultimate Tuf Combo License Plate Frame # CR62510 is 7 x 4-5/8-inches on hole centers as shown in the linked photo. This plate cover includes mounting nuts/bolts and decorative bolt head covers that match the frame. Both standard and metric hardware is included.

expert reply by: Adam R

0

click to enlarge

Answer 1

The distance between the mounting holes for the Pollak Heavy-Duty, 7-Pole, Round Pin Trailer Wiring Socket #PK11720 is 3" on center. I have attached a photo to demonstrate this as well as a review video where this measurement is shown. We also…

view full answer...

Answer 2

The easiest way to cut the oval hole for the Rubber Grommet, #a70gb, in my opinion, would be to use a Light Mounting Bracket for 6-1/2 inch Oval Trailer Lights, BK70BB, as a template and then use a hole saw the correct size to cut a hole on each end…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Mounting Hole Spacing of Ultimate Tuf Combo License Plate Frame CR62510

Product Page this Question was Asked From

Continue Researching