Is Camera Angle of GCH Truck Bed Cargo Camera Adjustable

Question

Question:

I have installed this camera and it functions great. I would like to adjust the camera to point down a little more to get a better view of my hitch but I am afraid I will break it trying to move it it’s very tight in the socket. It doesn’t seem to want to move. The description says it is adjustable

asked by: Wayne R

1

Helpful Expert Reply:

The ball socket of the Truck Bed Cargo Camera # 3460001 that you referenced is pretty tight but it is adjustable. What you'll want to do is use a small screwdriver to apply pressure into the screw hole I pointed out which will allow the socket to point down.

expert reply by: Jameson C

1

click to enlarge

Ed H.

6/27/2020

Is it possible to twist the camera the same way? My camera is crooked side to side

Chris R.

7/1/2020

I'm not quite sure what you mean. Did you try adjusting the camera as described above?

My R.

12/22/2024

@ChrisR my camera is showing the lines rotated slightly to the right and not centered. Is there a way to rotate to where the guiding lines align with the bed?

Kevin C.

12/23/2024

@MyR The guide lines will pop up in the same place on the screen so the only way to adjust them would be to adjust the camera's view. You can adjust the camera itself like Jameson talks about above or adjust the mounting bracket for the camera to fix the angle. I would check the mounting bracket with a level to help make this process easier since it's likely the smallest adjustment you'll need to get the view correct.

Answer 1

The Custom Third Brake Light Camera for 8" Factory Monitor #3460001 will allow you to view the camera on the 8" factory monitor on the dash of your 2021 Ford F-350 Super Duty. You can easily toggle between the rear bumper camera and the 3rd…

view full answer...

Answer 2

The Custom Third Brake Light Camera part #3460001 which is a fit for a 2020 Ford F-150 with 8" monitor installs rather easily with only a few connections. There is a plug that ties into the factory harness and then a switch which gets run to a…

view full answer...

Answer 3

The Truck Bed Cargo Camera for 8" Factory Monitor part #3460001 does feature a 150 degree angle image and 360 degree adjustable camera but what matters the most to you is that it is high enough above your truck bed that you'd be able to see…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Is Camera Angle of GCH Truck Bed Cargo Camera Adjustable

Product Page this Question was Asked From

Continue Researching