Grade Bolt to Use When Installing CE Smith Tie-Down Bracket # CE26214G

Question

Question:

What type or grade of bolt is required for this bracket

asked by: Brian

1

Helpful Expert Reply:

A Grade 5 bolt or higher would be recommended for use with the CE Smith Tie-Down Bracket # CE26214G.

expert reply by: Jameson C

1

Answer 1

We have the etrailer Ratchet Strap with Snap Hooks #e54BR which is 10' versus the Strap #e34BR you found which is 20'. Both of these have a 10,000lb break strength. If you are needing longer than 10' you can always cut the 20' strap…

view full answer...

Answer 2

It sounds like there is a short somewhere along the wiring of your vehicle or trailer that is causing a fuse to blow every time you connect. The first thing I recommend doing is disconnecting the trailer and using a circuit tester like #PTW2993 to…

view full answer...

Answer 3

Did it blow immediately after replacing it or did it blow after connecting a trailer? Either way the problem is a short to ground that is causing the fuse to blow and you'll have to find it and fix as needed. If the fuse blows without a trailer…

view full answer...

Answer 4

Did you have a 4-pin connector that had 5 wires or was it a 5-pin connector? There is a big difference since you normally see a 5-pin connector on a boat trailer with the 5th pin used for an electric reverse lockout solenoid on a brake actuating…

view full answer...

Answer 5

There are two types of 5-wire flat trailer wiring harnesses; the wishbone style of 4-pole such as #A35W42B which has 4 pins but that has two separate wires connected to the the running light pin so that you have one wire for each side of the trailer;…

view full answer...

Answer 6

The Hopkins Endurance Easy-Pull Harness w/ 4-Pole Flat Connector #HM38134 you referenced has 18 gauge wires for the brown (taillight), green (right turn and brake), and yellow (left turn and brake) wires. The white (ground) is a 16 gauge wire.…

view full answer...

Answer 7

Yes we do, Johnny. Check out the CE Smith Tie-Down Bracket for Boat Trailers #CE26214G. This is a bolt-on bracket that will create a fixed-position tie-down on your trailer, is made of galvanized steel, and is 4" long x 1 15/16" wide.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Grade Bolt to Use When Installing CE Smith Tie-Down Bracket # CE26214G

Product Page this Question was Asked From

Continue Researching