Brake Controller Recommendation for 2019 Honda Ridgeline

Question

Question:

I’m having a casita travel trailer built. My tow is 2018 Awd rtl Honda Ridgeline. The casita is a 2wire what do you think I need. I think a p3 controller a plug and play adapter and the adapter that hooks in at back seat and at 7way plug at rear bumper?

asked by: Monty

0

Expert Reply:

First let's get your 2019 Honda Ridgeline setup for a 7-way and brake controller. It sounds like you might have a 7-way already installed, but if you didn't the correct kit would be the part # 118288 which is a confirmed fit for your vehicle. The brake controller I recommend is the P3 part # 90195 that you referenced. This is the best performing controller and also the most advanced so it will do the best job for you overall. It has a screen that can display full words, the ability to save presets, and has onboard diagnostics.

To install the P3 requires the correct install harness which for that all you'd need is the part # 3070-P and you'd be set.

Since you are having the Casita trailer built you'll need to make sure you tell them you want brakes installed on the axle(s) and to have a 7-way RV connector installed as well. They'll know exactly what you mean as this is a very common route to go. You mentioned it being 2-wire which I believe you meant in reference to trailer taillight wiring. This is totally separate from brake output wiring.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Brake Controller Recommendation for 2019 Honda Ridgeline

Featured Help Information

Miscellaneous Media

Continue Researching