Which Value Circuit Breaker for Installing Primus IQ Brake Controller TK90160

Question

Question:

Question, When installing the wiring for a Primus IQ Brake Controller, where do they normal install/locate the 40A Auto Reset Circuit Breaker?

asked by: Walt F

0

Expert Reply:

When hardwiring a trailer brake controller like the Tekonsha Primus IQ # TK90160 either a 20-amp or 30-amp circuit breaker will provide operating power for the controller itself.

The choice depends on whether the trailer has one braked axle (use the 20-amp value # PK54520) or if it has two or three braked axles (use a 30-amp breaker # PK54230). The breaker should be mounted on the firewall, reasonably close to the battery positive terminal. The copper-colored terminal on the breaker connects to the battery.

We do include a 40-amp breaker in our Brake Controller Install Kit # ETBC7 and this one is for the 12V auxiliary power circuit on the 7-way which can power devices on the trailer. This value circuit breaker is not for the brake controller.

expert reply by: Adam R

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 4

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 5

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 8

We can get you everything you need for towing with your 2017 Toyota Sienna XLE. By plastic shield, I believe you are referring to the appearance panel underneath the Sienna, and that will have to trimmed a bit in each of the hitches available for the…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

It sounds like you may already have a 4 way connector on your vehicle, which is half of the battle. In order to operate the Curt Echo Mobile Wireless Brake Controller #C51180 you will need an almost fully functional 7 way connector; using something…

view full answer...

Answer 11

Hello Dan, We can most definitely get you set up to use your Redarc Tow-Pro Liberty brake controller in your 2022 Toyota Highlander. Since you were looking at the #ETBC7, I’m assuming your Highlander does not have the factory tow package. To equip…

view full answer...

Answer 12

Hi Michael! Do you already have a 7-way on your Transit? If you don't have wiring, you need to start by adding a 4-way with #C56327 (single rear wheel) or #C42MJ (dually). Once you have your 4-way installed you can upgrade it to a 7-way using the…

view full answer...

Which Value Circuit Breaker for Installing Primus IQ Brake Controller TK90160

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching