How Does Brake Controller Install in 2014 GMC Sierra 1500 Using Factory Install Harness

Question

Question:

I bought the brake control for my 2014 gmc sierra 1500 the plug is hooked to the back of the cubby hole in the light panel in wont work I found a harness under my seat it says glove box jumper what do i need to do to get my trailer brake control to work

asked by: Scott

0

Expert Reply:

The brake controller jumper wire you found in the glove box can be used to wire in the brake controller you have. I am not sure which controller you have but basically you'll plug the harness into the port under your dash for the brake controller install and then you'll wire it color for color to the brake controller's wiring and it will be wired in and ready to work.

expert reply by: Jameson C

0

Answer 1

On your 2014 GMC Sierra 1500 there is a junction box with a black cover on it located on the driver's side floorboard, way in the back, to the left of the brake pedal. There should be an empty spot to plug in the wiring harness located in the…

view full answer...

Answer 2

If you have the factory tow package on your 2014 GMC Sierra 1500, which from your description it sounds like you do, then the Curt Venturer Trailer Brake Controller #C74VV is plug-and-play. All you need is the Curt Custom Wiring Adapter #C51451; one…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

How Does Brake Controller Install in 2014 GMC Sierra 1500 Using Factory Install Harness

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching