Electric Brake Assembly for 12 Inch Hubs With 4 Bolt Mounting Flange

Question

Question:

I need new brake assembly it take 4 bolt flange to bolt brake assembly on it got 12x2 hubs

asked by: William S

0

Expert Reply:

There is one electric brake assembly that may be able to work for you, the Dexter Electric Brake Kit # 23-105-106-09. This kit fits standard 5-bolt mounting flanges or AL-KO/Hayes 4-bolt flanges; if you have this type of 4-bolt flange you would likely know it because the pattern is offset, with the upper mounting bolt holes spaced further apart than the lower holes.

These brakes are rated for 6,000 lbs and come with the mounting nuts but would require Brake Mounting Bolts # 7-5 and Lock Washer for Brake Mounting Bolts # 38LW.

I've added links to a couple video reviews of these brakes for you to check out.

expert reply by: Kyle S

0

Answer 1

For what you have you'd want the Electric Trailer Brake Kit - Self-Adjusting - 12" - Left and Right Hand Assemblies #AKEBRK-7-SA and you'd be set. This is a set of self adjusting brake assemblies that fit your axle/hub and will work…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 4

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 8

Hey Rob, thanks for reaching out. Yes, we do have dash-mounted brake controller options for your 2004 GMC Sierra 2500HD. If you want a standard controller that mounts on the dash, I recommend the following: - Curt TriFlex NEXT Trailer Brake…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 12

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Electric Brake Assembly for 12 Inch Hubs With 4 Bolt Mounting Flange

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching