5-Lug Hub Covers Compatible with Bearing Buddy Grease Caps

Question

Question:

I purchased the 5 lug hub covers and the bolt pattern fit but not deep enough to seat all the way down to the rim. The bearing buddy is in the way by about 1/4 inch. Do you sell deeper hub covers for bearing buddy clearance?

asked by: Robert

0

Expert Reply:

Hub cover # QT545C and similar item # PXQT545CHN both fit 5-on-4-1/2 wheels. If you are sure your Bearing Buddy grease caps are fully seated in the hubs and the covers # QT545C do not fit I suggest the item # PXQT545CHN. You can check out the linked video to see that this item works with these grease caps.

expert reply by: Adam R

0

Answer 1

It sounds like you need the QuickTrim Trailer Hub Cover #QT545C. Just to be sure this is designed for 5 on 4-1/2 inch bolt patterns and has an outside diameter of 6-3/8 inches.

view full answer...

Answer 2

The very end of center cap included with the Aluminum Viking Series Valhalla Trailer Wheel - 13" x 5" - 5 on 4-1/2 - Silver Spoke #AX02350545BMFL you were looking at is removeable without taking the wheel off so you will have no issues…

view full answer...

Answer 3

Thanks for that photo, and we do have an option for a ST175/80R13 trailer tire and wheel in chrome. From your photo it looks like you have the common 5 on 4-1/2" bolt pattern, but I do highly recommend verifying this if you aren't sure. I…

view full answer...

Answer 4

Hey Jim, we do have a replacement center cap for the Taskmaster trailer wheel part #AX02350545BMFL that you referenced with the part #CXF106C.

view full answer...

Answer 5

Yes, the Steel Directional Trailer Wheel - 13" x 4-1/2" Rim - 5 on 4-1/2 - Chrome Finish Item #AM48VR you were looking at would be capable of supporting your 4500 lbs trailer. Each wheel has a 1,660 lbs capacity which would put you well…

view full answer...

Answer 6

If the Phoenix USA QuickTrim Hub Cover for Trailer Wheels #QT545C will fit depends on the dimensions of the grease caps you have. The diameter of the interior at its narrowest point (nearest to the outside) is right around 2-1/4-inches, the depth…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

5-Lug Hub Covers Compatible with Bearing Buddy Grease Caps

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching