Replacement Latch Spring for Bulldog Collar-Lok Coupler Part # BD028288

Question

Question:

I am trying to locate and purchase just the springinch for this coupler. I do not need a repair kit that other places are trying to sell me. Is this possible ?

asked by: Lewis G

0

Expert Reply:

According to Bulldog, the replacement spring you are looking for is not individually available, but it can be purchased as part of latch repair kit, part # BD024200. This repair kit uses a different latch than your coupler does, but the spring is the exact replacement you are looking for.

expert reply by: Mike L

0

click to enlarge

Answer 1

I'm not sure what part you are referring to as the movable half. If you are talking about the sleeve and spring loaded clamp that fit around the hitch ball, you will need to replace the coupler. For a 2 inch ball, you will need something like the…

view full answer...

Answer 2

I have attached for you a photo that shows the proper sequence to couple and uncouple a Bulldog Collar-Lok Coupler like the part #BD028386. To summarize, see below: To Couple: 1) Block trailer wheels. 2) Align hitch ball beneath coupler. 3) If the…

view full answer...

Answer 3

Hello John, I was not able to find that information anywhere, luckily we have one on a trailer right outside. From the top of the mounting plate to the top of the jack is 20 1/4". What kind of trailer were you thinking about putting this on?

view full answer...

Answer 4

It sounds like you are used to using a Bulldog Collar-Lok Coupler, like part #BD028288, and that your new coupler is the Bulldog Collar-Lok Coupler w/ Pin, #BD028244, which is designed to be used as you have indicated. You have to grasp the coupler…

view full answer...

Answer 5

The distance between the center of the ball hole to the center of the circle used for A-frame jacks on the part #BD44125W0317 that you referenced is 12-1/2 inches. I confirmed this with my contact at Bulldog. The advantages between the latching…

view full answer...

Answer 6

Yes, you can drill holes into the Bulldog Collar-Lok Coupler w/ Low-Profile Latch #BD028288 to install it using the existing mounting hole configuration on your trailer.

view full answer...

Answer 7

Hello Ryan. The #CA-5196-B Ram Sleeve Lock A-Frame Trailer Coupler and the Bulldog #BD028288 are fairly similar. They are both 50 degree a-frame couplers designed for a 2" ball and both are about 16" long overall. The main difference is the…

view full answer...

Answer 8

Basically you will want to compress the spring part #BD500354 so that you can position it in place on your Bulldog Coupler. I attached a picture that shows where the spring installs at. It will just be a matter of compressing the spring to get it in…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Latch Spring for Bulldog Collar-Lok Coupler Part # BD028288

Continue Researching