Can Shank for Weight Distribution Hitch be Modified

Question

Question:

Are you able to cut a drop shank for a WDH? I currently have a EA-Z lift hitch that has a 2.5 inch drop and I am needing a 4, the only drop shanks that fit my need are longer and might scrape the ground. Can I cut the remaining shank that is not needed off?

asked by: Kyle

0

Expert Reply:

I do not recommend modifying a shank for a weight distribution hitch or cutting off any part of the shank; there is no way to guarantee any modified shank can work. Additionally, even though we do not carry EA-Z Lift products, I would be strongly willing to bet using a shank that was modified would void the warranty.

I have added a link to our selection of weight distribution shanks for you to take a look at as well.

expert reply by: Kyle S

0

Answer 1

Hey Kevin. The BulletProof Hitches Weight Distribution Shank for 2-1/2" Hitches item #BPH75RR has indeed been redesigned to have a second hitch pinhole. I have attached the new dimensional diagram below that I got directly from Bulletproof. The…

view full answer...

Answer 2

It sounds like the shank you have just doesn't give you enough drop; and whether or not you need a weight distribution hitch is honestly up to you. It should help level your trailer (if you have the appropriate drop), but it may not be a system…

view full answer...

Answer 3

Hey Aaron, thanks for reaching out! The Equal-i-zer Weight Distribution Shank #EQ94FR will be your best bet since it has a 9" drop compared to the 9-1/4" drop from your Curt Shank #C17132. If you can let me know what exact amount of drop…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hi James! With your GVWR being 7,600 pounds, your loaded tongue weight should be around 760 pounds. With that said, I recommend going with the Weigh Safe True Tow Weight Distribution Hitch - 2" Shank - 6" Drop - 8.5K GTW, 850 lbs TW…

view full answer...

Answer 11

Hey Mark, yes we do have a version of the Andersen part #AN88VR with a 2-5/16 inch ball instead with the part #AN53VR. What does your trailer weigh?

view full answer...

Can Shank for Weight Distribution Hitch be Modified

Featured Help Information

Miscellaneous Media

Continue Researching