Replacement 1157 Bulb for Wesbar Submersible Low Profile Trailer Tail Lights

Question

Question:

replace the BULB in a west bar 102641

asked by: Dick

0

Expert Reply:

If you have the Wesbar Submersible Low Profile Trailer Tail Lights # 403026 and # 403076 on your trailer, which the replacement lens # 102641 fits, then the correct replacement bulb is the 1157 part # A1157B on our site.

If you would like to replace them with red LED bulbs then we also have part # P231157R360 that you can use.

expert reply by: Jon G

0

Answer 1

Hello Daniel, thanks for reaching out. We may have a fender that will work for you, but there is no way for me to look up your trailer to know the exact specs for your fenders. Basically I would just need to know the length, width and height of the…

view full answer...

Answer 2

The Light Bulbs #A1157B & #A194B are replaceable on your Wesbar Tail Lights 403026. The part #102641 is the number for the lens while the 102640 is for the inner assembly which is only available with the entire tail light at this time.

view full answer...

Answer 3

The Fulton Single Axle Trailer Fender with Top and Side Steps #F008585 is also available as a 2-pack #F008585-2 for your 1999 Escort WT18GA Boat Trailer. These universal fit heavy duty fenders are designed for 15" wheel and tires and are capable…

view full answer...

Answer 4

I did a little research and was able to find that the wt18pa used #L44649 outer bearing, #L68149 inner bearing, and the #58846 grease seal. If you want to replace the entire hub you would use the Trailer Hub for 3,500-lb Axles - 5 on 4-1/2 -…

view full answer...

Answer 5

Ken, since the Wesbar 102639 is no longer available, you will need to replace both lights with the Optronics LED Combination Trailer Tail Lights #TLL160RK. These lights measure 8-1/16" long x 2-7/8" tall x 2-13/16" deep, has a built in…

view full answer...

Answer 6

In general, yes, most incandescent bulbs can be swapped out for an LED. In order to do this you need to know the bulb type such as 1157. That said, when replacing incandescents with LEDs you must use the same color bulb as the lens in order for the…

view full answer...

Answer 7

For an 1157 bulb like the #A1157B, in order to remove the old one you'll want to gently push down on the bulb while twisting the bulb 1/4 turn counterclockwise. You should then be able to pull the bulb from the socket. When replacing the bulb,…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement 1157 Bulb for Wesbar Submersible Low Profile Trailer Tail Lights

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching