Installing the CE Smith Heavy Duty Vertical Bunk Brackets

Question

Question:

When you drill the holes, do you drill straight through and let the hole alignment give you that inward slope?

asked by: Don

0

Expert Reply:

When you install the CE Smith Heavy Duty, Vertical Bunk Brackets - 85 and 95 Degree Set - Galvanized Steel # CE26233-34GA the brackets will give you the appropriate bend, so you will drill mounting holes after marking and removing the bracket. When installing the bunk board once the mounts are secured, you can drill directly through the board as you stated.

expert reply by: Jason S

0

Answer 1

From the base of the the CE Smith Heavy Duty, Vertical Bunk Brackets - 85 and 95 Degree Set #CE26233-34GA to the center of the top hole measures 6-1/8 inches.

view full answer...

Answer 2

Hey Danny. I took a look at our options and I do not have anything in a 9" roller and bracket that's going to work for your Holsclaw boat trailer. We have quite a few keel rollers like the 12" Wide item #CES94JR. You would need the…

view full answer...

Answer 3

Hello Harold, Looks like you already found the longest ones we have, the CE Smith Carpeted Bunk Boards for Boat Trailers - 7' Long - 1 Pair #CE27845. For some 10' boards, I would go to your local hardware store to get some 2"x4"…

view full answer...

Answer 4

For U-bolts for your 3" x 3" frame you will want something that is slightly larger. If the measurements were listed as exactly 3" it isn't going to fit. What you need is the CE Smith U-Bolts - Galvanized - 3-13/16" Long x…

view full answer...

Answer 5

Yes, you can run both of your trailer's brown wires to the single brown wire of your new 5-way. Typically this is how most 5-ways are wired. Your old one was a wishbone style connector which means it has the two wires already for that circuit.

view full answer...

Answer 6

You are correct. You will want to mount the longer 95 degree bracket of the CE Smith Heavy Duty, Vertical Bunk Brackets - 85 and 95 Degree Set #CE26233-34GA on the lower section of the angled crossmember on your boat trailer, and the 85 degree…

view full answer...

Answer 7

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 8

A lot of it depends on the length of the springs and equalizers that are used. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and 29-1/2"…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Installing the CE Smith Heavy Duty Vertical Bunk Brackets

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching