Fifth Wheel Installation Kit Options for a 2008 Ford F-350 Super Duty Short Bed

Question

Question:

I need to no what mounting bracket to buy to install my 5th wheel rails in a 2008 f350 short box . I have a reuse hitch. Do I need the reuse universal brackets or can I use the curt brand ?

asked by: Ron J

0

Expert Reply:

I recommend getting a new custom fit installation kit for your 5th wheel trailer hitch in your 2008 Ford F-350. Using a new kit will ensure the capability of all the parts and you will also get new hardware for installation.

For your truck, one option for a custom kit is # RP50082-58. This will include the brackets you have referenced, rails, and hardware. The Reese rails are compatible with Curt, Draw-Tite, Hidden Hitch, Reese, Valley and Husky 5th wheel hitches that fit in above the bed rails. I have included a link to the installation instructions for you and a link to a video showing a typical installation.

For a Curt kit, you can use # C16448-204. With this kit, you can also use Curt, Draw-Tite, Hidden Hitch, Reese, Valley and Husky 5th wheel hitches that fit in above the bed rails. I have included a link to the installation instructions for you.

expert reply by: Michael H

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Fifth Wheel Installation Kit Options for a 2008 Ford F-350 Super Duty Short Bed

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching