Comparing Draw-Tite and Curt Trailer Hitches on 2018 Ford Transit T250

Question

Question:

I'm looking for a trailer hitch for my 2018 Ford Transit T250. Can you tell me what the difference is between the Draw-Tite and Curt class 3 hitches?

asked by: Reggie R

0

Expert Reply:

Between the Curt # C13193 trailer hitch and Draw-Tite # 75912 trailer hitch that fit your 2018 Ford Transit T250 the biggest differences are the tongue weight and towing capacities of each hitch.

The Curt hitch is rated for 900 lbs of tongue weight and 6,000 lbs of towing capacity compared to the 750 lbs of tongue weight and 5,000 lbs of towing capacity for the Draw-Tite hitch, which is why I recommend the Curt # C13193 hitch for your '18 T250.

The hitches have a very similar installation and offer similar ground and bumper clearance so the relative strength of the Curt hitch due to its larger capcity is the tie-breaker; please keep in mind you will need to abide by the towing capacity in your T250's owner's manual. I have also added a link to a video install of this hitch for you to take a look at.

For wiring which will give you a 4-way connector and allow you to power your trailer's lights you need Wiring Harness # C56327. It is also recommended you use Dielectric Grease for Electrical Connectors # 11755 to help prevent any type of corrosion in your connector, which will increase its durability and extend its lifespan.

I also recommend checking out Ball Mount Kit # 989900, which is for 2” hitches and may fulfill your towing needs in one tidy package; two ball mounts - one with a 3/4” rise or 2” drop and the other with a 2-3/4” rise or 4” drop - a 1-7/8” hitch ball, a 2” hitch ball, and a pin and clip.

You can use the link to the help article on ball mounts I've added to determine if this kit will give you the correct amount of drop or rise. I've also attached a link to our pages with each of our ball mounts for you to check out.

expert reply by: Kyle S

0

click to enlarge

Answer 1

So I was unable to find your order based on your email or name, so I'm not sure which hitch you bought from us, but what I can tell you is that based on installations we've done, the trailer hitch for your 2019 Ford Transit T150 with the best…

view full answer...

Answer 2

If you have a trailer wheel that has a 6 lug setup you are going to have a bolt pattern of 6 on 5-1/2 inches. This is the standard 6 lug wheel bolt pattern that trailer rims have. If you are unsure you can check out the help article I attached that…

view full answer...

Answer 3

Hey Marc! You will not have to drill out or enlarge the holes on your 2025 Crosstrek to install the EcoHitch Stealth #EH57CR. If you take a look at our installation video below you will see Kevin had no issues getting the hardware in using the…

view full answer...

Answer 4

The Ford Transit if equipped with the factory tow package would have came with both a trailer hitch and trailer connector and they would both be located directly under the rear bumper so odds are you do not have either because they are not hard to…

view full answer...

Answer 5

Hey Daniel, the hitch we offer for your 2019 Ford Transit T250 that has the lowest profile is the Curt part #C14012 which has a concealed crosstube and only the hitch opening visible underneath the rear of the vehicle.

view full answer...

Answer 6

Hi Jerrod; the correct wiring harness for your 2025 Hyundai Santa Fe HTRAC AWD is the Curt T-Connector Vehicle Wiring Harness #C29ZV you were looking at. This will plug into the connection points in your rear cargo area and then a hot lead will run…

view full answer...

Answer 7

Hi Richard; have you tried testing the pin on the Curt 5th Wheel/Gooseneck #C53CR 7-way for power? I would start there. Since the light works on your trailer with the 7-way at the bumper I expect it to work with the gooseneck wiring as well. If you…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...