What Grease Seal is Needed for the Dexter Trailer Axle Beam Part # 7461121

Question

Question:

Will this hub fit axle part #7461121?

asked by: Cameron

0

Expert Reply:

Yes, the Dexter Trailer Idler Hub Assembly part # 8-231-9UC1-EZ is a confirmed fit for the Dexter Trailer Axle Beam part # 7461121. You may have noticed that the axle beam takes a 15123 outer bearing and the trailer hub takes a 14125A outer bearing. However, they both have a 1.25" inner diameter therefore can be exchanged for one another.

expert reply by: Conner L

0

Answer 1

The Dexter Trailer Idler Axle Beam with EZ-Lube Spindles #T20BTR-EZ-7258 should work great for your application! The only time that having your hub-face sit out an extra inch would be a problem is if that made your trailer tires touch fenders that…

view full answer...

Answer 2

The hub-face distance can be longer than your current axle, but you don't want it to be shorter otherwise you run the risk of the tire sidewalls making contact with your trailer frame. So if the 95" long hub-face for the Dexter Trailer Axle…

view full answer...

Answer 3

You may be able to replace your existing axle that has an 84 inch hub face length with one that has an 89 inch hub face length without a problem but it's going to be dependent on your existing spring center length. This is the distance from the…

view full answer...

Answer 4

We do have a straight Dexter axle that is very close to your Lippert one. The #7461121 will be 95 inches from hub face to hub face and 80 inches from center of one spring seat to the center of the other. The branding of the axle typically doesn't…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What Grease Seal is Needed for the Dexter Trailer Axle Beam Part # 7461121

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching