What is the Weight Capacity of a Dexter SLR P16 Axle

Question

Question:

I have a dexter p 16 axle model SLR , what is the weight cap.?

asked by: Wendell

1

Helpful Expert Reply:

If you can read me the serial number on the axle I can then call the manufacturer, Dexter, and find out the weight capacity but if not you can measure the diameter and use the chart below to determine axle capacity. The "P16" is the plant it was made.

- 1,000-lb - 2,000-lb Axles: 1-1/2 inch - 1-3/4 inch diameter
- 3,500-lb Axles: 2-3/8 inch diameter
- 6,000-lb - 7,200-lb Axles: 3 inch diameter
- 8,000-lb Axles: 3-1/2 inch diameter
- 9,000-lb Axles: 4 inch diameter
- 10,000-lb + Axles: 5 inch diameter

expert reply by: Conner L

1

Treff F.

4/12/2025

Serial number Dexter D 8227361

Robin H.

4/13/2025

@TreffF what specifically are you looking for? A replacement axle? Bearings, hubs, brakes? I can contact Dexter this week when they're open to have them identify the axle but that information would be helpful to have.

Treff F.

4/13/2025

@RobinH I would like to know the weight capacity of the axle and what replacement bearing/hub assembly I would need. Thanns

Robin H.

4/17/2025

@TreffF they weren't able to tell me the capacity, they said it is an older axle. I would assume 2k based on the possible bearings. They also cannot get the exact bearings. You either need # L44649 inner and outer bearings with # RG06-020 (10-60) grease seals or # L44643 inner and outer bearings with a 010-003-00 seal that we don't carry or have an equivalent for. Unfortunately, you're going to have to pull off your hubs and verify which set of bearings and seals you need.

Answer 1

You definitely can Lito! To swap out your manual brakes with self-adjusting ones, you'll want the Dexter Nev-R-Adjust Electric Trailer Brakes item #23-458-459. This is a left and right hand set that will replace one axles brakes. The Dexter…

view full answer...

Answer 2

If your 2020 Ford F-350 has the OEM prep package you'll see 4 "pucks" and a gooseneck hitch opening in the bed (pictured below). If it doesn't have pucks then you could install the Reese Under-Bed Gooseneck Trailer Hitch w/ Custom…

view full answer...

Answer 3

It looks like your current brakes use the offset 4-bolt mounting pattern. Take a look at the picture I have included that shows the mounting pattern of Dexter Electric Brake Kit for 4 Bolt or 5 Bolt Flange - 12" - Left/Right Hand Assemblies - 6K…

view full answer...

Answer 4

Most of our 12 x 2 electric drum brake assemblies like Dexter left/right kit #23-112-113 use a 5-bolt mounting pattern but the Dexter brake kit #23-105-106-09 has both 4-bolt and 5-bolt mounting holes. I went to our warehouse and measured the spacing…

view full answer...

Answer 5

Thanks for the information! Based on the information you provided my contact at Dexter was able to confirm that you have a 3500lb axle with a 94.5" hub face to hub face measurement and an 81" spring center to spring center measurement. For…

view full answer...

Answer 6

It sounds like your assemblies are not the typical assemblies and will need to be replaced. For your brake assemblies, I recommend the Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-7-SA along with mounting hardware #BRKH12. If you don't…

view full answer...

Answer 7

The wheel you referenced was made in China. See follow up response below for USA made option!

view full answer...

Answer 8

We definitely have Dexter brake assemblies to fit a Dexter 5,200 lb axle like you have. The part #AKEBRK-7-SA is a kit that includes a left and right hand assembly for a 5,200 lb axle like what you have. These are self-adjusting too which means that…

view full answer...

Answer 9

The reason your trailer is heavily leaning to one side is because of the way it's loaded. From the picture, it appears that you have much more equipment on the right side than you do the left side. This uneven loading has caused the leaf spring…

view full answer...

Answer 10

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 11

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 12

The Dexter "8-248" is a hub assembly for 3,500 lb axles that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in both 5 on 4-1/2" and 5 on 4-3/4" bolt patterns therefore you would need to…

view full answer...

What is the Weight Capacity of a Dexter SLR P16 Axle

Product Page this Question was Asked From

Continue Researching