Does Round Snap Ring Swivel Jack w/ Footplate # TJB-2002S-B Bolt or Weld to Trailer

Question

Question:

What are the measurements on center for the four bolts on the mounting plate?

asked by: Zach

0

Expert Reply:

Actually the bracket of the Round Snap Ring Swivel Jack w/ Footplate # TJB-2002S-B that you referenced is designed to be welded to the trailer frame. There would not be enough room to fit bolt heads between the bracket and the bracket it pivots on that's on the hitch body.

expert reply by: Jameson C

0

Answer 1

Hey Andrew, thanks for reaching out. We do have a jack that can be used to replace your Shelby 5756A, but it isn't a direct replacement. If you want something that will match up with the current snap ring bracket, we have the Round Snap Ring…

view full answer...

Answer 2

Based on my research, the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will be a perfect replacement for your Shelby 5756A trailer jack. This jack will allow you to use the existing snap ring jack mount on your trailer for installation.…

view full answer...

Answer 3

Hey Dan. If your jack mount has a 2-1/2" ring on it then the Round Snap Ring Swivel Jack w/ Footplate item #TJB-2002S-B is going to be your best option. This 2,000 lbs capacity jack attaches to the same size bracket that the Fulton item…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Does Round Snap Ring Swivel Jack w/ Footplate # TJB-2002S-B Bolt or Weld to Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching