How to Determine if the Thule Hullavator Pro Will Fit the Roof Rack on a 2007 Toyota Highlander

Question

Question:

Will the Thule hullivator fit on roof racks on my 2007 Toyota Highlander? Thanks

asked by: Cathie

0

Expert Reply:

I can give you some stipulations for the Thule Hullavator Pro # TH898 to fit the roof rack on your 2007 Toyota Highlander, but I wouldn't be able to verify a fit without knowing the following information about your current roof rack.

You roof rack crossbars need to be spaced at least 24" apart on center, with 28.5" of load bar space for the Hullavator Pro, and 4" - 8" of space beyond the feet of your roof rack (see attached picture). As long as your roof rack meets all of these requirements you can definitely use the Hullavator Pro! If not just let me know and I can recommend a roof rack for you.

Also keep in mind that your vehicle's roof must have a load capacity of at least 130 lbs to use the Hullavator.

expert reply by: Jon G

0

click to enlarge

Answer 1

To attach the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs #TH898 to your 2021 Toyota Highlander you'll need a roof rack that has a T-Slot in the crossbars for the Hullavator to slide into. Currently the only brand of roof…

view full answer...

Answer 2

To carry two Thule Hullavators kayak carriers #TH898 on the roof of a vehicle you'd need to have a roof rack with longer bar lengths as each of these takes up about 28.5 inches of bar space. So your best roof rack setup for your 2013 Toyota…

view full answer...

Answer 3

I have a couple possible solutions for you to transport your kayak with your 2017 Toyota Tacoma, however there is not a standard ladder rack available that is compatible with the Extang Encore Tonneau Cover. This is because the hardware for the…

view full answer...

Answer 4

To install Thule's load-assist Hullavator kayak carrier #TH898 on a vehicle's roof rack the ends of the bars must extend out past the roof rack feet by at least 4-inches. You can see this requirement illustrated in the linked diagram. The…

view full answer...

Answer 5

We do have a Single Yakima HD Crossbar #Y35FR which you can pair with the Two Towers #Y62TR. You will need the Adapters #Y03541 which we only carry as a set of 4 along with either the Front #Y06145 or Rear #Y06128 fit kit depending on if you plan on…

view full answer...

Answer 6

The Yakima HD Crossbars #Y01156 will work with the Thule Hullavator #TH898. Based on the pictures you sent in it looks like you have the crossbars installed upside down. The end caps have an opening on the other side that lets you easily slide in…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

How to Determine if the Thule Hullavator Pro Will Fit the Roof Rack on a 2007 Toyota Highlander

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching