bing tracking image
Customer Service My Orders
Q & A Icon

Hard to Remove Bezel on Atwood RV Carbon Monoxide and Propane Gas Detector  

Published 08/08/2018

Question:

How do I remove the bezel for my Atwood RV Carbon Monoxide and Propane Gas Detector - 12 Volt...? I don’t want to crack the bezel, I tried pushing the tabs but it wouldn’t release...please help

0

Expert Reply:

Those tabs are the answer. They can be pretty tight so you may need a small screwdriver to push them in. If you can get one side or end started then it will be easy to pull the cover off the Atwood RV Carbon Monoxide and Propane Gas Detector # AT36681.

A colleague suggested using a hair dryer to warm up the tabs so that they will be more flexible and less likely to break.

expert reply by:
0
Michael H

Video/Article/FAQ this Question was Asked From

Article or Video
Q & A Icon

Continue Researching

See More Q&A Expert Answers >>
Explore Expert Info Our Expert
on RV Gas Detectors

Videos

Help Articles

Expert Answers

Others Also Watched
Review of Peterson Electrical Tools - Trailer Frame Wire Clip - PET93NV
Review of Rhino Rack Roof Basket - Replacement Wind Fairing - RR94BY
The Low-Down on the Wind Fairing for Front Runner Slimline II Platform Racks
Ultimate Overview of the Redarc Solar Panel Wind Fairing Mounts
Breaking Down the LED Trailer Tail Light w/ Reflector and Bracket
How to Choose a Trailer Brake Controller
An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
Redarc Tow-Pro Liberty Brake Controller Review RED24FR
Measuring To Choose The Right Trailer Axle
Clean Up Your Trailer Wiring
What to Know About the Curt TriFlex NEXT Trailer Brake Controller
Others Also Read
Trailer Wiring Diagrams
Brake Controller 7- and 4-Way Installation Kit (ETBC7)
How to Measure for Trailer Hitch Drop
5 Things to Know About Weight Distribution Hitches
Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
How to Measure Your Trailer Wheel Bolt Pattern
Trailer Lighting Requirements
30-Amp and 50-Amp RV Service: What's the Difference?
How to Choose the Right Trailer Hitch Class
Brake Controller Installation: Starting from Scratch
The 5 Best Trailer Drop Hitches You Can Buy
What are the Common Types of Propane Fittings Used on RVs?
Others Also Asked
Recommended Replacement For Atwood LPCO Detectors

Hey Charlie, That's the detector's way of telling you that it's at the end of its lifespan and needs to be replaced. LP gas detectors typically have a 5-7 year lifespan. Since the LPCO 30094 detects both lp gas and carbon monoxide…

view full answer...
Resetting the Atwood RV Carbon Monoxide and Propane Gas Detector AT36681

The instructions state the rest/test button of the Atwood RV Carbon Monoxide and Propane Gas Detector - 12 Volt - White #AT36681 is the button on the top right, and you need to press that in and hold it down. If the rest does not work and the red…

view full answer...
Troubleshooting Atwood RV Carbon Monoxide Detector Beeping Every 40 Seconds

We've seen this issue before on your Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 and the beeping every 40 seconds indicates "a fault has been detected that compromises some detector function." What you need to do is use…

view full answer...
Troubleshooting the Atwood RV Carbon Monoxide and Propane Gas Detector AT36681

It sounds like your Atwood RV Carbon Monoxide and Propane Gas Detector part #AT36681 is hooked up properly and is getting power. The code you hear is like you said a fault code in this case because of the audible tone. I recommend replacing it. The…

view full answer...
Replacement Carbon Monoxide Detector for Atwood 36681

You could use the 2-wire Propane Gas and Carbon Monoxide Detector part #RS34FR in place of the Atwood 36681 that you referenced. This would fit in the cut out you have now and has a flange that is large enough that would cover the hole.

view full answer...
How Does Atwood Carbon Monoxide Detector #AT36681 Remove From Wall

On the top of the Atwood Carbon Monoxide detector part #AT36681 there are two tabs you need to depress to pry the bezel off the front of it which will then show you the screws/hardware that secure the detector to your wall.

view full answer...
How to Remove Lens From Command LED Trailer Tail Lights #328-003-85L and #328-003-85

The LED Trailer Tail Light w/ Reflector for the Drivers Side #328-003-85L and Passenger Side #328-003-85 have small notches on the lens that hold it in place. A Pick Set #PT76VR will allow you to get behind the lens to pry the lens off of the tabs as…

view full answer...
Atwood RV Carbon Monoxide and Propane Gas Detector Beeps Even After Reset

If the Atwood RV Carbon Monoxide and Propane Gas Detector part #AT36681 continues to beep even after a rest then this can be narrowed down to either a leak or faulty detector. If you shut off the gas supply to the trailer entirely and the alarm still…

view full answer...
How Long Should Life of Atwood Carbon Monoxide and Propane Sensor Last

The lifespan of Atwood carbon monoxide and LP sensors like the part #AT36681 that you referenced is 7 years so if you are having alarms go off at 2-1/2 years I'd recommend taking the alarms seriously. You can also make sure the batteries that it…

view full answer...
Installing Atwood RV Carbon Monoxide and Propane Gas Detector

When replacing your existing detector with the Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 you will not need to disconnect the 12V trailer batteries. It also does not matter which of the two power wires you connect first. The third…

view full answer...
What is the Difference Between a Class II and a Class III Hitch?

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...
Lug Nut Torque Chart for Trailer Wheels

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...