Can Aftermarket Brake Controller be Installed on 2012 Ford F-450 With Integrated Brake Controller?

Question

Question:

I am building a flatbed on a 2012 F450 cab and Chassis truck for a friend. It was a government truck bought at an auction by a dealer and then sold to my friend. It has the factory integrated trailer brake control system on it but I’m not sure if it’s working. Is it possible to install an aftermarket brake controller on this truck that will simply plug in to the existing wiring harness with the use of and adapter harness.

asked by: Wes H

0

Expert Reply:

Yes, you can install an aftermarket brake controller on your friend's 2012 F-450 cab and chassis that will simply plug in, although you are going to get an error code and to remove it you will need to go to a local Ford dealer and have it turned off.

As for the brake controller itself, I strongly recommend the Prodigy P3 # 90195 along with Adapter # 3034-P. The Prodigy P3 is the most popular model we carry due to its effectiveness and ease of use. It will activate your trailer's brakes immediately in proportion to the F-450's brakes and offers three different boost levels so you can adjust your braking power.

The P3 levels automatically, has constant diagnostic checks, contains safeguards which defend your controller against shorts, and features an LCD display which is much easier to read than that of other controllers. This controller has been met with nearly universal praise; it has been reviewed by our customers more than 2,000 times and is averaging close to 5 out of 5 stars.

expert reply by: Kyle S

0

Answer 1

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 2

For your 2022 Ford F-450 cab & chassis, and your Tekonsha Prodigy P2 #90885, the correct wiring adapter is the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers #22292.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Can Aftermarket Brake Controller be Installed on 2012 Ford F-450 With Integrated Brake Controller?

Continue Researching