Size of Hub/Drum Compatible with Titan Uni-Servo Hydraulic Brake Kit T1878800-700

Question

Question:

Will your 10Titan hydraulic brake set work with my existing drums?

asked by: John M

0

Expert Reply:

The Titan Uni-Servo Hydraulic Brake Kit # T1878800-700 consists of a left and right pair of brake assemblies that fit with 10 x 2-1/4-inch hub/drums like # T1543900CB042. Please refer to the linked photo to see how a drum is measured. To mount the brakes on your 4-bolt brake flanges you can use hardware kit # BRKH10A; this kit allows installation of a pair of 10-inch brakes.

expert reply by: Adam R

0

click to enlarge

Answer 1

For your brake assemblies I recommend the Demco Hydraulic Brake Kit - Free Backing - Galvanized - 10" - Left/Right Hand Assemblies - 3.5K #40716-15. These assemblies are galvanized to resist corrosion and will not require a reverse lockout for…

view full answer...

Answer 2

I do not see an extension kit for the Demco Hydraulic Brake Line Kit for Single Axle Trailers #DM5426. However, you can just step up to the Demco Hydraulic Brake Line Kit #DM5643 which has the additional main line (long run) length that you are…

view full answer...

Answer 3

Since your tandem axle trailer only has brakes on one of the axles, you will just need a single axle kit like the Kodiak Hydraulic Brake Line Kit #18SI-BLKIT you were looking at. This kit includes an 18 foot, 7 foot and 1-1/2 foot long flexible brake…

view full answer...

Answer 4

Yes the hydraulic drum brake kit part #T1878800-700 that you referenced do come fully assembled.

view full answer...

Answer 5

Hi Chad! That 4 bolt mounting plate with 2-7/8" measurement is pretty much the standard for 3,500 pound axle brakes (which the Dexter 8-247 drum also fits), so that makes it nice and easy. We have a lot of option, but I recommend the two I have…

view full answer...

Answer 6

Hi Ed, In regards to the 3,500 lb Demco Hydraulic Brake Kit #40716-15 and the Hydraulic Trailer Brake Kit #AKUBRK-35-D, starting with the country of origin, the Demco are made in the U.S. and the opposing brakes (made by AxleTek) are made in China.…

view full answer...

Answer 7

Yes, the Titan Hydraulic Brake Kit part #T1878800-700 is exactly what you need. The mounting holes are spaced 2-7/8" apart on center which is an industry standard for the 4 bolt brake mounting flanges. They measure to be 10" in diameter and…

view full answer...

Answer 8

To determine the brake assemblies that will fit your trailer, you would need to know your axle's weight capacity, the size of your wheels, your mounting flange bolt pattern and the inside diameter and depth of your hub. Depending on the type of…

view full answer...

Answer 9

We have a TruRyde brand that will fit as a replacement for what you have. For a pair, you would need #RG06-050. Or for one double lip seal, #58846. To be sure, you can check the measurements of your seal. The measurements will have to be as accurate…

view full answer...

Answer 10

That is a Timken seal with the part number 171255TC, so you can use the Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 1 #58846 as the replacement or you can get a pair with part #RG06-050.

view full answer...

Answer 11

Hello Gregg, I think I can help shed some light on what is going on. Basically, there are two ways to stop surge brakes from actuating when backing up the trailer. The first and most popular way to do this is to use a surge brake actuator with a…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Size of Hub/Drum Compatible with Titan Uni-Servo Hydraulic Brake Kit T1878800-700

Products Featured in This Question

Continue Researching