Do Titan Hydraulic Brake Assemblies T1878800-700 Come Fully Assembled

Question

Question:

I am going to replace my hydraulic brake system on my boat trailer. It is one with the lock out on the actuator. It is a 10inch drum with 2 1/4 pads. I am looking at purchasing Titan Trailer Brakes - T1878800-700. I was wondering if these come fully assembled for bolt on application? Thanks

asked by: Les W

0

Expert Reply:

Yes the hydraulic drum brake kit part # T1878800-700 that you referenced do come fully assembled.

expert reply by: Jameson C

0

Answer 1

Yes, the Titan Hydraulic Brake Kit part #T1878800-700 is exactly what you need. The mounting holes are spaced 2-7/8" apart on center which is an industry standard for the 4 bolt brake mounting flanges. They measure to be 10" in diameter and…

view full answer...

Answer 2

Hi Chad! That 4 bolt mounting plate with 2-7/8" measurement is pretty much the standard for 3,500 pound axle brakes (which the Dexter 8-247 drum also fits), so that makes it nice and easy. We have a lot of option, but I recommend the two I have…

view full answer...

Answer 3

Hi Ed, In regards to the 3,500 lb Demco Hydraulic Brake Kit #40716-15 and the Hydraulic Trailer Brake Kit #AKUBRK-35-D, starting with the country of origin, the Demco are made in the U.S. and the opposing brakes (made by AxleTek) are made in China.…

view full answer...

Answer 4

The Titan Uni-Servo Hydraulic Brake Kit #T1878800-700 consists of a left and right pair of brake assemblies that fit with 10 x 2-1/4-inch hub/drums like #T1543900CB042. Please refer to the linked photo to see how a drum is measured. To mount the…

view full answer...

Answer 5

To determine the brake assemblies that will fit your trailer, you would need to know your axle's weight capacity, the size of your wheels, your mounting flange bolt pattern and the inside diameter and depth of your hub. Depending on the type of…

view full answer...

Answer 6

That is a Timken seal with the part number 171255TC, so you can use the Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 1 #58846 as the replacement or you can get a pair with part #RG06-050.

view full answer...

Answer 7

We have a TruRyde brand that will fit as a replacement for what you have. For a pair, you would need #RG06-050. Or for one double lip seal, #58846. To be sure, you can check the measurements of your seal. The measurements will have to be as accurate…

view full answer...

Answer 8

Hello Gregg, I think I can help shed some light on what is going on. Basically, there are two ways to stop surge brakes from actuating when backing up the trailer. The first and most popular way to do this is to use a surge brake actuator with a…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Do Titan Hydraulic Brake Assemblies T1878800-700 Come Fully Assembled

Continue Researching