3" Gooseneck Hitch Ball Needed for a 2017 Ford F-350 with OEM Pucks

Question

Question:

I need a goosneck kit for a 2017 Ford F350 with the round base, 3 inch ball and 30k weight capacity. thx.

asked by: Kevin M

0

Expert Reply:

For a 3" gooseneck hitch ball that is compatible with the OEM puck system on your 2017 Ford F-350 Super Duty we have the Reese Pop-In Ball # RP19314 which has a 30K weight capacity. For the safety chain loops you can use part # RP58468.

Unfortunately the B&W Ball and Safety Chain Kit # BWGNXA2061 that you referenced does not come in a 3" gooseneck ball version, only the 2-5/16" for the OEM puck system in your F-350.

expert reply by: Jon G

0

Answer 1

We do have just the safety chain loops for the Ford factory fifth wheel rail kits like you have. For that you'd want the part #RP58468 and you'd be set.

view full answer...

Answer 2

You actually have a couple of options to add safety chain loops to the factory 5th wheel prep package on the 2011 and newer Ford trucks. First, #RP58468 does fit but you could also use #C60691. The Reese ones #RP58468 measure 2 inches by 1-3/8 inches…

view full answer...

Answer 3

It sounds like you have the OEM pucks on your 2012 Ford F-450. If this is the case then I recommend using the safety chain loops #RP58468 which I confirmed with my contact at Reese will work with the Reese Safety Chain Kit #RP49151 for your Goose…

view full answer...

Answer 4

If you can send me a photo of the trailer jack I would be more than happy to help you find a replacement, but unless the jack is still under warranty we won't be able to swap it outright with what came on your trailer when you purchased it.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Rob, I’d be wondering the same thing if I came across a ball mount made out of aluminum like the #BPH77MR while researching. Totally fair question. That said, I haven’t seen any noticeable difference in slop or wear compared to their steel…

view full answer...

Answer 10

Hi Hilario, congrats on the new truck! ^___^ If this were my truck and I was installing a retractable cover on it (which I actually did with my Silverado), I would go with the manual RetraxPRO XR Hard Tonneau Cover - Retractable - Aluminum - Matte…

view full answer...

Answer 11

Hey Tyler, thanks for reaching out. I'm sorry to say no, we don't have a 5 on 4-1/2" hub, or any hub for that matter that fits a 3/4" straight spindle. That kind of spindle was really only seen on older trailers and is basically…

view full answer...

3" Gooseneck Hitch Ball Needed for a 2017 Ford F-350 with OEM Pucks

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching