Modifications Needed to Install Curt Class I Hitch C11362 on 2015 Lexus ES 300h
Updated 06/04/2018 | Published 05/31/2018
Products Featured in This Question
Question:
I am looking at a curt class 1 trailer hitch for my 2015 Lexus ES300H. I have two questions: 1. How far below the existing bumper does the hitch protrude when installed? Does that leave enough clearance to the road? 2. does the bumper need to be cut? I look forward to your reply - thank you in advance
asked by: Bob K
Helpful Expert Reply:
The Curt Class I trailer hitch # C11362 that fits your 2015 Lexus ES 300h will require some modest modifications to your vehicle during installation. You can refer to the written instructions I linked for you to see the step-by-step process as well as the tools needed. These mods include removal and trimming of the heat shield so it can be re-installed and some trimming of the underbody panel.
In the instructions a photo showing the finished installation is included. Naturally there is some reduction in ground clearance but the hitch will be installed as close as possible to the bottom of the bumper cover. The bottom of the hitch tube will be approximately 2-1/4-inches below the bumper cover.
If you will use the hitch for a bike rack please note you are limited to use of a 2-bike Class I carrier and note also that Curt recommends using support strap # 18050 to help handle some of the weight of an installed bike rack.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- For Towing
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: Roof Rack
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Search Results: how to return an order
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Q&A: Recommended Trailer Hitch for 2013 Lexus ES350 for Best Visual Appearance
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: Curt Powered Tail Light Converter Installation - 2023 Kia Telluride
- Shop: Brake Controller
- Search Results: trailer tires and wheels
- Video: Clean Up Your Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Search Results: trailer jack
- Q&A: Comparing the Curt Hitch C13416 and EcoHitch Hitch 306-X7396 for a 2019 Toyota RAV4
on Trailer Hitch
