3 inch Waste Valve Seal Recommendations

Question

Question:

Im looking for extra Seals for a tank Waste Valve Body 3

asked by: Charbel Z

1

Helpful Expert Reply:

We have two different sets of 3 inch waste valve seals. We have the part # T1003-7VP which is for the new style Valterra valves and the part # T1003-9VP which fits the older style

expert reply by: Jameson C

1

Answer 1

For a 3 inch waste valve, you'd want to use the Valterra #T1003-7VP kit. The #T1002-7VP kit is for 2 inch valves, and wouldn't work with your 3 inch valve.

view full answer...

Answer 2

As a clarification, all valves, including the #T1003VPM, include seals, as pictured in picture 10 on the product page. However, I can see that your 3" waste valve is missing it's seals. I would not buy a new complete valve when all you need…

view full answer...

Answer 3

Go ahead and send me the pictures and I'll take a look to see which 1-1/2 inch Valterra seal you would need. The biggest visual difference is that the new Bladex Style part #T1001-9VP has a small lip on one corner of it that's used for…

view full answer...

Answer 4

The seals you need for a 3 inch Valterra Bladex waste valve is the part #T1003-9VP actually. The part you referenced is for the older style valves.

view full answer...

Answer 5

We describe the Valterra Replacement Seals and Hardware Kit #T1003-7VP as being intended for the "old style" 3-inch waste valves. This is also how they are described on the Valterra website. The 9VP kit #T1003-9VP is for use with the Bladex…

view full answer...

Answer 6

I don't really have an exact write-up on replacing the seals for a Valterra Waste Valve like part #T1001B but I do have some info which may help. If you have a 3" then you can use part #T1002-7VP. This kit comes with both seals, front and…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

3 inch Waste Valve Seal Recommendations

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching