Load Stops to Fit the T-Slot of Yakima JetStream Aero Crossbars

Question

Question:

I have a 2005 Chevy Silverado 1500 with an ARE cap. It has the Yakima Jet Stream rack. Which load stops will work for carrying a ladder?

asked by: Karen M

0

Expert Reply:

We have a couple load stops that work in the Yakima JetStream aero bars but they aren't actually Yakima products.

We had a customer test the Thule load stops, part # 753-3761, and they worked perfectly. Then we also have an employee who tested the Rhino-Rack load stops that fit their Vortex Aero bars, part # RRRLH2, and they were also a fit.

expert reply by: Charles S

0

Answer 1

Yes, it is possible. To add a roof rack to your 2022 Toyota C-HR, without rails that does not overhang, I recommend the roof rack by Yakima which includes the following parts: Yakima BaseLine FX Roof Rack for Naked Roofs - Aero Crossbars - Aluminum -…

view full answer...

Answer 2

We put stickers on everything we take pictures and shoot videos of. Sometimes they're more obvious than others but they're always there. It's not specifically for branding it's actually to help protect ourselves from getting our…

view full answer...

Answer 3

The Rhino-Rack Vortex StealthBar Roof Rack #JA7970 actually has rubber coated stainless steel straps which secure it to the raised rails on your 2023 Subaru Outback Wilderness. So you won't have issues with the straps failing. If you are only…

view full answer...

Answer 4

If you are looking for crossbars that can accommodate the 12mm T-slots, the closest confirmed top channels we have are Yakima crossbars like the Yakima HD Crossbars - Aluminum - Black - 68" #Y01158 or Rhino-Rack crossbars like the Rhino-Rack…

view full answer...

Answer 5

You can use a set of load stops like the Rhino Rack Aero version, part #RRRLH2 to limit the canoe's travel across the bars. These handy stops include a local tie-down point so you can strap the canoe down with cam straps. There's a great…

view full answer...

Answer 6

I wish that was a part that Thule offered but at this time the only solution we have would be the Quick Grip part #TH05738 that you referenced.

view full answer...

Answer 7

The rubber pieces that are on the claws of the Replacement Quick Grip Mount Assembly #TH05738 aren't available separately so if yours are no longer there and you are wanting to replace them you will need a whole new mount assembly.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Load Stops to Fit the T-Slot of Yakima JetStream Aero Crossbars

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching