Kodiak Disc Brake Assembly for 3,500 lb Axle Compatibility with Spindle Dimensions

Question

Question:

Attached are the dimensions and pictures of my spindle

asked by: Kevin L

1

Helpful Expert Reply:

The Kodiak Disc Brake Assembly - 10" Hub/Rotor - 5 on 4-1/2 - 3,500 lbs # K2HR35DKG will fit spindles that measure 1.063 inches at the outer bearing, 1.378 inches at the inner bearing, and 1.719 inches at the seal location. It also fits brake flanges that have the 4 bolt mounting pattern.

Unfortunately the photo you sent with dimensions did not come through, so I can't see if they are compatible. If you have further questions please let me know.

expert reply by: Jason S

1

click to enlarge

Kevin

5/16/2018

Attached are the dimensions and pictures of my spindle

Jason S.

5/16/2018

Thanks for the spindle measurements and photo. The Kodiak Disc Brake Assembly - 10" Hub/Rotor - 5 on 4-1/2 - 3,500 lbs # K2HR35DKG will work great for you, but you will want a different grease cap. I recommend # DC200L-DCRP for your EZ Lube Spindles.

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Kodiak Disc Brake Assembly for 3,500 lb Axle Compatibility with Spindle Dimensions

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching