Will a Fulton Trailer Jack Fit the Same Weld On Mount Used by a Shelby Jack

Question

Question:

I have a Shelby weld on trailer jack that is rated for 750 lbs. I want to switch to higher weight rated jack = 1200lbs. Can I reuse the same welded bracket that is already on the trailer?

asked by: Lori

0

Expert Reply:

It is possible that you can reuse the same mount. It depends on the style of the jack you have and the one you want to replace it with.

For example, the Fulton Round, Snap-Ring Swivel Marine Jack, # FTJ120W0301, has a mounting bracket with an inner diameter of 2-1/2 inches. It uses a 3/8 inch pull pin. If it does not match what you have on the trailer, the jack does come with a new weld-on bracket that you can use.

expert reply by: Michael H

0

Answer 1

Thank you for providing the part number 2228 from your Fulton jack. I checked with Fulton but could not find this reference number. If the jack is 10-years old or older it may no longer be in their product line since many higher-capacity jacks were…

view full answer...

Answer 2

Hi Todd, I do have a drill-powered A-frame jack for your enclosed trailer that meets all of your needs, and what I recommend for you is the Lippert Quick Drop Tongue Jack #LC733926. The #LC733926 just requires a 3/4" socket which you can use…

view full answer...

Answer 3

The Dutton-Lainson A-Frame Trailer Jack #DL22530 is currently our only manual A-Frame tongue jack with a 2" outer tube. The Lippert Quick Drop Tongue Jack #LC733926 that supersedes your 423192 jack along with our other jacks have all gone to the…

view full answer...

Answer 4

It is possible the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit the same mount used by your Shelby 5776 jack but we do not have the exact dimensions of the mount used by your Shelby jack so you will need to take a quick…

view full answer...

Answer 5

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784.

view full answer...

Answer 6

The Fulton Bolt-Thru Swivel Marine Jack #FXP15W is a bolt through replacement option for you. This is designed to use a welded plate like the Jack Mounting Bracket for Fulton Marine Jack #P9012-00. It appears like you have a bolt that goes into a…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Will a Fulton Trailer Jack Fit the Same Weld On Mount Used by a Shelby Jack

Continue Researching