Distance Between Bed Rails for Installation of Curt E5 16K Fifth Wheel Hitch
Updated 01/25/2013 | Published 08/10/2011 >
Question:
My fifth wheel hitch was in my shop when it burned earlier this year and I was looking at your Curt 16K pound hitch as a replacement. I just need the hitch since my rails are already mounted in my 2004 Chevy 2500 pickup. I wanted to know if the distance between the rails is standard for most hitches and what the measurement is for the Curt hitch in particular. Thanks.
asked by: Ron J
Expert Reply:
Do you know who manufactured your existing bed rails?
The Curt E5 16K Fifth Wheel Hitch you referenced, part # C16115 are compatible with universal rails manufactured by Reese, Curt and Valley. A universal rail will have three mounting slots on each side of the rail, as shown in the photo with dimensions I have linked to.
Your front and rear rail should be 22 inches apart, measured from the center of the front rail to the center of the rear.
Product Page this Question was Asked From
Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs
- 5th Wheel Hitch
- Fixed 5th Wheel
- Above Bed Rails
- 4000 lbs Vertical Load
- 16000 lbs GTW
- Double Pivot
- Economy - Slide-Bar Jaw
- 13-1/4 - 17 Inch Tall
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: bed rails
- Shop: Fifth Wheel Hitch
- Search Results: 5th wheel and gooseneck wiring custom fit vehicle wiring
- Shop: Trailer Wiring
- Shop: PullRite's ISR SuperRail Mounting Kit - 20K - Fits Ford F-250 & F-350 w/ Aluminum Bed
- Shop: Curt Custom Fifth Wheel Installation Kit for Ford - Carbide Finish
- Shop: Curt Custom Fifth Wheel Installation Kit for Ford F250 and F350 - Carbide Finish
- Shop: Curt Custom 5th Wheel Installation Kit for Ford - Gloss Finish
- Shop: Curt Custom Fifth Wheel Installation Kit for Chevy/GMC - Carbide Finish
- Shop: PullRite Custom Installation Kit w/ Base Rails for 5th Wheel Trailer Hitches - 20K
- Shop: Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7' Long
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Video: B&W Companion OEM 5th Wheel Hitch Manufacturer Breakdown
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Search Results: trailer tires and wheels
- Search Results: fifth wheel hitch
- Article: How to Measure for Trailer Hitch Drop
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
- Shop: Gooseneck Hitch
- Article: How to Measure Your Trailer Wheel Bolt Pattern



Lance
1/25/2013
My old 1-ton Powerwagon has a universal rail set, and I run everything in it. Ive got a Reese 15k Pro fifth-wheel rig that s in, and a Curt gooseneck plate that also s into it. When not in use, I can pull both out, and with a couple of pieces of spacer plywood between bed headboard, to rail, to rail, to tailgate ped in place, I have my smooth, flat truckbed back again to carry anything from plywood to furniture in it.Yes, by design, the tab-slots should be 22-inches on center. If you really work your rig a lot, like I do, you may find that new in gadgets have to be eased into the slots, as they may or may not be exactly 22-inches on center.If only someone would make a -in truckbed 1k crane for my rails, Id be the first to some money on a crane setup to lift and lower propane and oxyacetylene torch tanks into my truckbed.