What is the Length of the 1.980" Bearing Buddy Bearing Protectors # BB1980A-SS

Question

Question:

What is the length of this once installed into a hub assembly?

asked by: Adam S

0

Expert Reply:

I have linked a picture showing that the Bearing Buddy Bearing Protectors # BB1980A has a full length of 1-3/16" while the part that inserts into the hub is 5/16". This means that the Bearing Buddy will stick out 7/8" from your hub.

The only difference between the Bearing Buddy # BB1980A and the Bearing Buddy # BB1980A-SS that you referenced is that the former is chrome plated while the latter is stainless steel. They both have the same dimensions though.

expert reply by: Jon G

0

click to enlarge

Answer 1

The model 1980 Bearing Buddy simply means that they fit a 1.980 inch hub bore. There is one difference of note between Bearing Buddy Bearing Protectors #BB1980A (Chrome Plated) or #BB1980A-SS (Stainless Steel) and the Bearing Buddy Bearing Protectors…

view full answer...

Answer 2

All the 1.98" Bearing Buddy Protectors listed below are the same height at just under 2". Stainless Steel w/ Auto Check #BB1980A-SS Stainless Steel #BB84SR Chrome w/ Auto Check #BB1980A Chrome #BB24SR

view full answer...

Answer 3

I would certainly recommend the 1/2-inch wire loom #459075-1. It will hold two jacketed 2 wire 10-gauge wire and three jacketed 2 wire 12-gauge wire. See pictures to the right. In addition, I was able to fit comfortably eleven individual 16-gauge…

view full answer...

Answer 4

If the shackles are flipping the wrong direction frequently that typically means the leaf springs are too short, the hanger spacing is too big, or the shackles are too short. Most of the time it's somebody changed leaf springs and just went with…

view full answer...

Answer 5

Hey Kelly, thanks for reaching out! When you replaced everything, were they exact replacements as far as dimensions and weight ratings go? Are your shackle straps in good condition?

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...