Replacement Brake Fluid Cap For Brake Actuators For Trailers

Question

Question:

I have a fleet of trailers. I am looking for replacement brake fluid caps for DEMCO Da-66b and ATWOOD 6000 lb 2 inch ball also. Please let me know if I can buy just the caps. Thanks.

asked by: Mike

0

Expert Reply:

We have some of what you need. For your Demco, we have the Demco Actuator Cap for Master Cylinder, Item # 3876. Spare parts for your Atwood needs are hard to find and we do not have any in our available inventory unfortunately.

expert reply by: Brint H

0

Answer 1

The Replacement Master Cylinder Assembly #T4395100 will not work to replace your Atwood master cylinder model 85841. Since replacement parts for your actuator are obsolete, your only option is to replace the entire actuator assembly. The Demco…

view full answer...

Answer 2

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 3

You can use bearing protectors on a hub with electric brakes. You have to make sure you are using a double lip seal though because a single lip seal is more likely to blow and allow grease to leak out and get all over the hub and brake components.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Brake Fluid Cap For Brake Actuators For Trailers

Product Page this Question was Asked From

Continue Researching