Recommendation For Replacement Trailer Jack For 2000 Mastercraft Boat Trailer

Question

Question:

I have a 2000 Mastercraft Boat trailer with a welded on jack bracket. It looks like the mounting holes are 4 inch on center horizontal X 2 3/4 inch vertical. Do you have a replacement jack with wheel that will bolt on?

asked by: David

0

Expert Reply:

The Round Swivel Marine Jack with Wheel, Item # MJ-1500B, comes close to the dimension you sent and has several different mounting options. The mounting bracket is 6-7/8 inches long x 5-3/4 inches wide. The mounting hole options are:

2-7/16 inches from center of top hole to center of nearest hole
3-7/16 inches from center of top hole to center of middle hole
4-7/16 inches from center of top hole to center of bottom hole
5-1/2 inches from center of left holes to center of right holes

This Jack has a retracted height of 13 inches and an extended height of 24 inches. It has a bolt-on installation and all the hardware is included. It has a corrosion-resistant zinc finish which makes it very durable and great for marine applications. It has a 1500-lb weight capacity and works with trailers with frame height from 2 inches to 4 inches.

I am attaching a link to our available inventory and to some videos for you to check out.

expert reply by: Brint H

0

Answer 1

Each of these gas shocks are rated for use individually and not in pairs so the part #372-5300-30 with it's 30 lbs rating would be how much it could lift by itself. So a pair of these would cover your 60 lb trunk lid. Now with that said your…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Recommendation For Replacement Trailer Jack For 2000 Mastercraft Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching