Replacement Steering Stabilizer Shock for Demco Kar Kaddy 2

Question

Question:

We bought our Kar Kaddy 2 new around 1980. It has no remaining legible stickers of ID. We need a new steering stabilizer shock for it. Do you have one?

asked by: Larry C

0

Expert Reply:

As a matter of fact we do. I spoke with a representative of Demco who told me that the Replacement Steering Stabilizer Shock for Demco Kar Kaddy # DM01729-30 will work with the Kar Kaddy 2.

expert reply by: Kyle S

0

Answer 1

If the steering stabilizer shock on your Demco Kar Kaddy SS Tow Dolly part #DM9713045 has gone bad then the wheels on the tow dolly may shimmy a bit while driving down the road or you will see oil around where the shock mounts as this would point to…

view full answer...

Answer 2

Replacement Steering Stabilizer Shock #DM01729-30 is the correct current replacement part for your Kar Kaddy 3 and it also fits the Kar Kaddy SS model tow dolly. I verified this item in Demco's Kar Kaddy specs.

view full answer...

Answer 3

Hello Simon. We do offer the Demco Kar Kaddy SS Tow Dolly #DM9713045, and we do have a few various replacement parts available. Let me know if there is something specific you are looking for. Some of our part numbers will be the same as the Demco…

view full answer...

Answer 4

I have attached a video for you to help you bleed the surge brakes and also given an explanation below. You want to top off the master cylinder and pump the fluid from the master cylinder. You can do this by unbolting the plate that holds the lever…

view full answer...

Answer 5

Hi Billy, For the Demco Kar Kaddy SS Tow Dolly #DM9713045, go with 500 ml of brake fluid. Also be sure it's DOT-3 or DOT-4 brake fluid, per the instructions.

view full answer...

Answer 6

We've got the owner's manual for the Demco Kar Kaddy SS Tow Dolly with Disc Brakes #DM9713045 linked just below as "Instructions for DM9713045".

view full answer...

Answer 7

You'll need to grab a multimeter like #PT89ZR and set it to DC voltage and then take a look at your pigtail connector on the motorhome side that connects to the #LC379145. There are four wires for this pigtail; Yellow: 12v Ignition - Retracts the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Replacement Steering Stabilizer Shock for Demco Kar Kaddy 2

Product Page this Question was Asked From

Continue Researching