Adjusting Cable Handle of Valterra Waste Valve Bodies

Question

Question:

How do you adjust the cables for the TC1372 ? The t handles have extended out and pushed the access door open. It looks like the inner cable length could be adjusted at the valve so the t handles dont stick out so far. Please help ! Thanks

asked by: Rick

0

Expert Reply:

There is a screw nut adjustment at the lever end that can be adjusted, This could have been turned inadvertently over a period of time lengthening the cable. Turning back out should lengthen the distance of the shield making it close tight.

expert reply by: Jameson C

0

Answer 1

Yes, the Valterra EZ Valve Electric Waste Valve for RV Black Water Tank #E40B-8 can be oriented sideways so it's able to open up under your trailer. The 3" to 3" hubs mentioned in the description are included with the valve. These are…

view full answer...

Answer 2

You'll definitely need to straighten that line out otherwise you'll keep having issues with cable not wanting to fully close the gate. You can remove the four bolts that mount the gate valve to the pipe and see if turning it 90 degrees and…

view full answer...

Answer 3

The valves you are seeking to replace are made by many different manufacturers and are a standard size. The function of the valve is what you want to pay attention to as there are T-handle and cable options and then of course black water versus gray…

view full answer...

Answer 4

The Valterra Waste Valve Bodies w/ Flexible Cables for RV Black Water and Gray Water Tanks - 72" Item #TC1372 is a correct replacement for your gray and black tank valves. I have attached a picture from the guide to help with placement of the…

view full answer...

Answer 5

Hi David, thanks for reaching out! The older Go Power PWM-30 Solar Controller has been discontinued, but you can use the Go Power PWM Solar Charge Controller with Bluetooth #GP76QR along with the Installation Adapter Plate #GP86QR to replace it! I…

view full answer...

Answer 6

In order to fix your loose cable on your LaSalle Bristol Cable-Actuated RV Waste Valve for Black Water Tank #34466N4AB36GM, you will need to tighten the set screw that holds the cable to the valve stem. To do this. you're going to need to first…

view full answer...

Answer 7

We describe the Valterra Replacement Seals and Hardware Kit #T1003-7VP as being intended for the "old style" 3-inch waste valves. This is also how they are described on the Valterra website. The 9VP kit #T1003-9VP is for use with the Bladex…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Adjusting Cable Handle of Valterra Waste Valve Bodies

Product Page this Question was Asked From

Continue Researching