Replacement Trailer Grease Seal that Inner Diameter 1.688 and Outer Diameter 2.328

Question

Question:

What is the thickness of a #168233 grease seal ? Im looking for the NOK AD2527E grease seal ID 1.688 OD 2.328 Thickness 0.5inch

asked by: Alejandro G

0

Expert Reply:

The thickness of the Redline Grease Seal # 168233 seal is 0.38. However, thickness is not always a dimension associated with picking out a suitable replacement seal. Typically it is the outer diameter and the inner bearing for picking out a replacement seal.

Based on the NOK number and the dimensions you listed this is a match.

expert reply by: Jameson C

0

Answer 1

The closest option we have that would work is the part #010-180-00 which has an inner diameter of 1.68 inches and an outer diameter of 2.33 inches.

view full answer...

Answer 2

Based on previous information we have for your UFP HD-1377-10 hub it uses the following components. I do recommend pulling one of your hubs to verify that the replacements listed below match your current parts. Inner Bearing #L68149 (Inner diameter…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Trailer Grease Seal that Inner Diameter 1.688 and Outer Diameter 2.328

Product Page this Question was Asked From

Continue Researching