Recommended Roof Rack System for KB Voodoo Truck Bed Rack

Question

Question:

thanks for following up. These crossbars are adjustable. Do you have a crossbar in mind that could fit this?

asked by: Reymond

0

Expert Reply:

For your KB Voodoo Truck Bed Rack, I recommend the Rhino-Rack Roof Rack System w/ 2 Vortex Aero Crossbars - Track Mount # Y02-490B. This will allow you to adjust the crossbars as needed to fit your roof box. It also gives you the option to remove the towers and crossbars when not in use. This system will give you a 220 lb weight capacity. I've attached a video to assist.

expert reply by: Jason S

0

click to enlarge

Reymond

2/20/2018

thanks for following up. These crossbars are adjustable. Do you have a crossbar in mind that could fit this?

Jason S.

2/20/2018

I didn't realize that you had adjustable crossbars on the KB Voodoo. There are not specific roof rack systems for that type of application. I still recommend using the track system and using your adjustable rails to support the frame of your rack. The issue if you were to mount only to the current crossbars is the lack of support from twisting and torque. The tracks supply you with a wider base for the front to back movement. I don't recommend just adding height to your system without additional support.

Answer 1

I would be happy to help you find roof racks for both your 2015 Toyota Tacoma Double Cab and your camper shell. I'll start out with the roof rack for your truck. It is the 2015 Toyota Tacoma Roof Rack by Yakima. These 60" wide heavy-duty…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Recommended Roof Rack System for KB Voodoo Truck Bed Rack

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching