Passenger Side Trailer Taillight Recommendation to Match Driver Side Taillight # STL9RB

Question

Question:

WHY can I not find the PASS. side light to go with..Trailer Tail Light - 7-Function - LED - Submersible - 14 Diodes - Red Lens - Driver Item # STL9RB

asked by: BILL S

0

Expert Reply:

The passenger side trailer taillight to match the part # STL9RB is the part # STL8RB.

expert reply by: Jameson C

0

Answer 1

Yes we do Danny, check out the Optronics LED Trailer Tail Light #STL78RPG. This is a submersible LED tail light that has 10 diodes, a 3 wire design, and measures 7-9/16" long x 3-5/16" tall x 3/4" thick.

view full answer...

Answer 2

Hey Daran, The numbers you gave don't correspond to any light I could find, but it's easy to find the right one. All you have to do is measure your current tail lights and find the one that most closely matches your measurement, and also know…

view full answer...

Answer 3

I went out in to our warehouse and pulled a Optronics Trailer Light #STL78RB and a Snap-on Reflector Ring for STL78RB Series LED Lights #A78RXB to show you what they look like together. I attached a picture and a video I shot also.

view full answer...

Answer 4

The wheel used on the Kenda Karrier 205/75-15 #AM32418DX wheel/tire combo has a 3.19 pilot diameter, so you'll want to choose a center cap with the same diameter. I'd recommend the Lionshead #LHCS102-SI60C which is constructed of stainless…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Passenger Side Trailer Taillight Recommendation to Match Driver Side Taillight # STL9RB

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching