Pop up Trailer Winch Operation to Lower Roof for Towing

Question

Question:

How do I get a pop up on a 1999. To reverse and go down

asked by: Thomad

0

Expert Reply:

Without knowing the make and model of your pop-up camping trailer, all I can do is give you some general help. It sounds like you can get your pop-up camper roof up but are not able to get it to ratchet back down for towing. There is often a reverse pawl that you need to switch if you have a standard hand winch that will allow you to slowly let the top back down. In order to switch the cam lever, you may need to first add tension to the gears by raising the roof slightly and then moving the pawl when there is not weighted tension on it.

I've attached a video that shows this. Let me know if you have further questions.

expert reply by: Jason S

0

Answer 1

If you're going to use a winch to raise and lower your popup you will want a winch that power loads both in and out. With a winch that will only power load in you will only be able to raise the popup and not lower with the winch. We have the…

view full answer...

Answer 2

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Hey Matt, Furrion typically has 4 wires running to their thermostats and the Chill Cube Thermostat #LC74DX is no exception. The harness you see with the thermostat would plug into the Chill Cube's controller and has 4 wires to extra wire to to…

view full answer...

Answer 9

Hey Neil. The 18,000 Btu Furrion Chill Cube RV Air Conditioner item #LC34DX fits a 14-1/4" x 14-1/4" cutout which is pretty standard on RV's. If you meant to write Dometic instead of domestic then yes it'll fit in your existing…

view full answer...

Answer 10

Hi JD; the Furrion Chill Cube #FR49TD air distribution box has a vent on it you can open and close. See the picture attached below. When it is closed it forces more of the air through the ducted system. Assuming you have a ducted system you will need…

view full answer...

Answer 11

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Pop up Trailer Winch Operation to Lower Roof for Towing

Featured Help Information

Miscellaneous Media

Continue Researching