Curt Sway Tab Weld On Position For Ball Mount and Friction Sway Control # 83660

Question

Question:

Just receive my order and need to know Which is the correct position to weld the sway tab to the ball mount? - Reese sway control kit PN 83660 has drawing that shows sway tab welded such that sway ball is 1 3/8” forward of tow ball - curt sway tab PN 45822 has drawing that shows sway tab welded where sway ball would be even with tow ball Which is correct? Or are they both acceptable?

asked by: Bob

1

Helpful Expert Reply:

You will want to mount the tab # C45822 to work with the sway bar you are using. I recommend following the Pro Series instructions of # 83660 for best function since that is the friction sway bar you are utilizing. I've also included the diagram to help with the location of the tab for both width and depth so you will also want to ensure it is 5-1/2 inches on center from ball to ball.

expert reply by: Jason S

1

click to enlarge

Ben

10/10/2024

Can it be farther than 5 1/2 inches from hitch ball? If so what is the max in between the two balls?

Reply

Jameson C.

10/10/2024

@Ben I would say you really gotta make sure you stick around 5-1/2 inches. Any more than that and it would probably bend the unit and break it around tighter corners.

Reply

Ben

10/10/2024

@JamesonC Thank you!

Reply

Jameson C.

10/10/2024

@Ben Glad to help!

Reply

Answer 1

The Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger #PD4560K18LS8 would be the correct replacement and is designed for 50 amp service, so this replacement would work for your Jayco 336 FKDS.

view full answer...

Answer 2

If there isn't a brand name printed on a tag somewhere on the actual landing gear it is not easy to determine because they all look and function the same way. The nice part about that is that if you need to replace parts or complete systems they…

view full answer...

Answer 3

Yes, you can wire the Rear View Safety Cigarette Lighter Adapter #RVS-505 to your Fantastic Fan #FV802250. All Fantastic Fans, including #FV802250, use the same "pancake style" motor which draws 4 amps so in order for a portable power bank…

view full answer...

Answer 4

Assuming that when you tested the resistance of the brakes you were testing the two wires on each magnet and getting 2.0 and 2.8 ohms the magnets on your trailer are not working correctly and will need to be replaced. For 7" brakes you should…

view full answer...

Answer 5

For the dual friction you are looking for, I recommend adding the Reese Friction Sway Control Kit - Economy - by Draw-Tite, Reese and Hidden Hitch #83660 to your hitch ball. This adjustable friction sway bar can be added using the Reese Sway-Control…

view full answer...

Answer 6

Since your roof extends up you'll want to go with a wall mount awning like the Thule HideAway Awning #TH490011 to avoid any interference. This will come with carriage bolts and brackets to secure it to the wall of the vehicle. I do recommend…

view full answer...

Answer 7

We can get you a replacement for your TDE LP75 disc brake actuator; that's a 7,500 lb actuator that accepts a 2" hitch ball, and the correct option will depend on if your trailer tongue is 3" wide x 4" tall or 3" wide x…

view full answer...

Answer 8

Typically, you want to mount the sway control bar, like the Curt Friction Sway Control #17200 that you referenced, on the passenger side of the trailer. This is so that if any maintenance needs to be performed on the side of the road, it can be done…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

The handle is actually the on/off switch for the unit and the bolt under the handle is the tension adjustment bolt. You will need to turn the On/Off handle clockwise (tighter) until the handle will stay firmly in place parallel with the main body of…

view full answer...

Answer 11

The #3442 replacement sway control tab would be welded onto the side of a ball mount, and the 1-1/4 inch diameter trailer ball would mount in the 5/8 inch diameter hole in the tab. If a ball mount with a 3/4 inch rise or a 2 inch drop would work,…

view full answer...

Answer 12

Since vehicles that have 2-1/2 inch hitches don't normally use friction sway control as it's not normally needed there aren't any brackets for the smaller balls of the units that are setup for that hitch size but I do have a solution…

view full answer...

Curt Sway Tab Weld On Position For Ball Mount and Friction Sway Control # 83660

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching