Total Length of a Pro Series Round, Pipe-Mount Swivel Jack # PS1401080303

Question

Question:

What is the total length of this jackPS1401080303 including the handle when it is retracted? I want to mount this jack on the back end of a low boy trailer and I have limited space. Thanks for your time.

asked by: Danny

0

Expert Reply:

I went out into our warehouse and measured a Pro Series Round, Pipe-Mount Swivel Jack # PS1401080303 and found that it is 26-1/2 inches from the top of the jack to the bottom of the footplate. And then it is 35 inches if you spin the jack handle around to where it is pointing vertically in the air.

I attached a couple pictures of these measurements for you to check out also.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For additional pipe mounts to use with the Pro Series trailer jack #PS1401080303 that you referenced you'd want the #BD015273. This is 1-7/8 inch long and 2-1/2 inch diameter.

view full answer...

Answer 2

I went to our warehouse to provide you a few measurements of the Pro Series pipe mount swivel jack #PS1401080303. The length of the entire swivel jack in the retracted position is 26-3/4 inches. The foot plate is 3-3/4 inches wide and 7-1/2 inches…

view full answer...

Answer 3

The Round, Pipe Mount Swivel Jack w/ Footplate #TJP-2002S-B uses a 9/16" Diameter pull pin. Just like the replacement pull pin and chain #TJP-PN916. The hole on the mount is just over 9/16" so that the pin can fit. I attached a short review…

view full answer...

Answer 4

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Total Length of a Pro Series Round, Pipe-Mount Swivel Jack # PS1401080303

Continue Researching