Replacement Pipe Mount to Use with Pro Series Jack # PS1401080303

Question

Question:

Im interested in purchasing this stabilizer jack: PS1401080303. I want to also purchase additional brackets to weld to my trailer so i can move the jack to different spots. What are the dimensions of the male bracket that welds to the trailer that comes with the jack length, diameter, pin hole size, etc.? And do you offer this bracket separately?

asked by: David

0

Expert Reply:

For additional pipe mounts to use with the Pro Series trailer jack # PS1401080303 that you referenced you'd want the # BD015273. This is 1-7/8 inch long and 2-1/2 inch diameter.

expert reply by: Jameson C

0

Answer 1

There is no bolt-on style jack made for a round tube trailer frame since this would make securing the jack rather difficult. The jack would want to rotate around the frame tube whenever it was under load. Your only option is to weld a jack mount onto…

view full answer...

Answer 2

Hello Jack, Yes, you can mount the Erickson #EM77316 Spare Trailer Tire Bracket to a round trailer frame, but it requires a few modifications since the bracket is originally designed for square or flat frames. The included U-bolts are shaped for flat…

view full answer...

Answer 3

You are correct that all bolt-on trailer jacks require a square or rectangular frame member for installation. There is no bolt-on jack made for a round tube trailer frame since this would make securing the jack rather difficult; it would want to…

view full answer...

Answer 4

Round frame trailer make installing a jack interesting. It's going to require some welding but you could use a swivel jack like part #FTJ120W0301 which comes with a weld on bracket and a wheel like you need.

view full answer...

Answer 5

I believe I have just the jack for you. Take a look at Pro Series Round, Pipe-Mount Swivel Jack, #PS1401460303. I went out to the warehouse and measured this jack and it will fit around a 2 inch diameter tube and uses a 9/16 inch pin. It is a short…

view full answer...

Answer 6

The pipe mount replacement for the Round, Pipe Mount Swivel Jack #TJP-2001-B that you referenced is the part #TJP-IP916.

view full answer...

Answer 7

The Pro Series Round Pipe-Mount Swivel Jack #PS1401460303 includes a weld-on steel tube that measures 2-inches in diameter. This tube, or the one already on your trailer, accepts the larger mating tube on the jack itself and is secured with the…

view full answer...

Answer 8

From the center of the pipe mount to the top of the etrailer jack #TJP-2002-Z measures 4-1/4 inches.

view full answer...

Answer 9

I went out into our warehouse and measured a Pro Series Round, Pipe-Mount Swivel Jack #PS1401080303 and found that it is 26-1/2 inches from the top of the jack to the bottom of the footplate. And then it is 35 inches if you spin the jack handle…

view full answer...

Answer 10

I went to our warehouse to provide you a few measurements of the Pro Series pipe mount swivel jack #PS1401080303. The length of the entire swivel jack in the retracted position is 26-3/4 inches. The foot plate is 3-3/4 inches wide and 7-1/2 inches…

view full answer...

Answer 11

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Pipe Mount to Use with Pro Series Jack # PS1401080303

Continue Researching