Replacement Step Module for Kwikee Revolution Series Steps PN 1510000

Question

Question:

hello. Im Son. I would like to buy a step module. pin number is 1510000 140 REV QA date code: 111061 Thank you.

asked by: Son

0

Expert Reply:

I spoke to my contact at Lippert Components (LCI) and they informed me that the Lippert Components Kwikee Revolution Step Control Module part # LC363980 is the correct replacement model for your Lippert Components Kwikee Revolution Steps pn (1510000).

expert reply by: Conner L

0

Answer 1

While I could not get the video to play, it sounds more like a control unit issue rather than a motor issue. The control unit should sense when the steps are closed and shut off the power for retracting and not spasm. Since you mentioned so many…

view full answer...

Answer 2

I have included the correct replacement parts for your 2012 Tiffin Open Road with Kwikee Series 41 steps below. - Replacement Motor for Kwikee Electric RV Steps #LC379147 - Replacement Gear Box and A Linkage for Kwikee Electric RV Steps #LC379160 -…

view full answer...

Answer 3

If you are looking to replace an entire vent assembly the most common cut out dimensions are 14-1/4" x 14-1/4". As to not disturb the roof sealant you can remove the inner garnish on the vent from inside your 2018 Forest River Sunseeker.…

view full answer...

Answer 4

The correct step control for you is the Lippert Components Kwikee Step Control with Override and PKD part #LC379605, not the Lippert Components Kwikee 9510 Control for IMGL/9510 Step Control part #LC379146 or the Kwikee Revolution Step Control Module…

view full answer...

Answer 5

To test your Control Module #LC379605 you'll need a 12v battery and an extra wire harness #LC369243 to connect the control module to the battery. You'll unplug the connector from the wire harness running to your motorhome's wiring and…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 12

Welcome back Mike! To attach a set of steps to your Palomino 1251 truck camper, I recommend the TorkLift GlowStep Camper Scissor Steps item #TLA7804. They're going to bolt directly to your Palomino right below the door, with the included…

view full answer...

Replacement Step Module for Kwikee Revolution Series Steps PN 1510000

Product Page this Question was Asked From

Continue Researching