How to Install a Brake Controller on a 2015 Jeep Wrangler Unlimited with Factory Tow Package

Question

Question:

Thank you very much for your help. I have ordered the products as your recommended. I plan to test the Jeep Wrangler towing the airstream, but assuming that goes well I need to look at the hitch situation. The previous owner handed over a collection of weight distributing hitch gear (ball mount, bars, etc.), but I'm thinking we'll start fresh with new equipment better-suited to our towing situation. It might not be absolutely essential, but I think it might tow better with a weight-distributing hitch. The Jeep has the sway control built into the ABS - but not sure how effective that is. The Jeep came with the 2" receiver, but I don't know if it is suitable for a weight-distributing setup. The specs I have for the airstream show a hitch weight of 350 lbs (2" ball), but I plan to use (2) 30 lb gas tanks in order to supply a compact propane generator. Also I assume we'll need a break-away safety switch. Finally, I need whatever we come up with to be something that my wife can manage by herself. What do you recommend hitch-wise for our situation? I'm open to a new hitch for the Jeep if required for WD setup.

asked by: Joe H

0

Expert Reply:

I have exactly what you will need for your 2015 Jeep Wrangler Unlimited to tow your Vintage Airstream with brakes. The first thing you will want is a 7-way trailer connector at the rear of the vehicle and for this I recommend the Hopkins Endurance Quick-Install 7-Way Trailer Connector part # HM42190 which is a direct plug and play option that will not require you to cut or splice any wires/circuits. The square plug on the end of this connector will plug into and replace the 4-way trailer connector you have which is found near the driver's side taillight housing.

The next thing you will need is a brake controller and the most popular, well reviewed, and easy to use one we sell is the Tekonsha Prodigy P3 Trailer Brake Controller part # 90195. This controller gets its reputation from the easy-to-read LCD display, integrated safeguards, and 5 storable settings.

In order to install said brake controller you will also need the Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers part # 5506. This is the only part of the installation that will require you to cut/splice any wires but I have attached an installation video of this very same harness/controller on a very similar 2017 Jeep Wrangler Unlimited for reference. Unfortunately, as the Jeep does not have a factory brake controller harness this will be your only option to install a brake controller.

expert reply by: Conner L

0

Joe

12/12/2017

Thank you very much for your help. I have ordered the products as your recommended. I plan to test the Jeep Wrangler towing the airstream, but assuming that goes well I need to look at the hitch situation. The previous owner handed over a collection of weight distributing hitch gear (ball mount, bars, etc.), but I'm thinking we'll start fresh with new equipment better-suited to our towing situation. It might not be absolutely essential, but I think it might tow better with a weight-distributing hitch. The Jeep has the sway control built into the ABS - but not sure how effective that is. The Jeep came with the 2" receiver, but I don't know if it is suitable for a weight-distributing setup. The specs I have for the airstream show a hitch weight of 350 lbs (2" ball), but I plan to use (2) 30 lb gas tanks in order to supply a compact propane generator. Also I assume we'll need a break-away safety switch. Finally, I need whatever we come up with to be something that my wife can manage by herself. What do you recommend hitch-wise for our situation? I'm open to a new hitch for the Jeep if required for WD setup.

Conner L.

12/12/2017

Thank you for your purchase, we certainly appreciate your business. If the gross trailer weight (GTW) of your trailer is more than 50% of your gross vehicle weight rating (GVWR), the use of a weight distribution system is recommended. In order to be sure you are choosing the correct weight distribution system, you will want to find the total tongue weight of your towing setup by adding the tongue weight of both your loaded ready to tow trailer and any cargo stored behind the rear axle of the tow vehicle. The average total tongue weight (TTW) rating of a trailer is typically 10-15% of the gross trailer weight (GTW). An easy way to find this would involve using a tongue weight scale like the etrailer Trailer Tongue Weight Scale part # e99044. When choosing a weight distribution system, you will want your total tongue weight to fall in the middle of the weight distributions weight capacity. For example, the ideal weight distribution system for a total tongue weight of 600 lbs. is one that is rated for 400-800 lbs. of tongue weight. There should be a sticker on your factory trailer hitch receiver that will state the capacities for a hitch with a weight distribution system if allowed. If you factory trailer hitch does not allow for the use of a weight distribution system then you can replace it with the Draw-Tite Max-Frame Trailer Hitch Receiver part # DT78MR (see install video attached). This hitch has a max GTW and TW rating of 4,500 lbs and 675 lbs respectively though you will need to determine the max GTW and TW allowed for your vehicle and go with the lower of the two ratings. To determine the maximum trailer weight capacity you can tow with your Jeep, you will need take your Gross Combined Weight Rating (GCWR) and subtract that by the the Gross Vehicle Weight (GVW) of your vehicle from the (GCWR) that will give you the maximum Gross Trailer Weight (GTW). This can all be found on the information tag located inside the driver door jamb. For a total tongue weight between 100-400 lbs, I recommend taking a look at the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control part # EQ37040ET or part # EQ37060ET for a total tongue weight between 200-600 lbs. The Equal-i-zer weight distribution systems are considered to be one of the best on the market. I have attached a review video on one of the systems for you as well. In regards to a breakaway system, this may or may not be required depending on the state you live in and their individual regulations for towing a trailer. Should you end up needing a breakaway system then I recommend using the Hopkins Engager Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger part # 20099.

Robert R.

5/24/2020

Hi. I have a 2017 Jeep Wrangler Unlimited Rubicon. It came with a towing package, including 2inch receiver and flat 4 wire connector. I need to add or change to a 7 pin to tow a travel trailer w/brakes. What product do I need if I wish to install an Autowbrake on-trailer brake controller? Does the tow package mean I have a 12v supply for the trailer mounted brake controller AND the trailer battery charging?

Chris R.

5/27/2020

In addition to the trailer signal light circuits you already have with the 4-Way on your Jeep Wrangler Unlimited - the Autowbrake # 3430001 just needs the 12V battery charge circuit from the tow vehicle for operation. Since your Wrangler has the factory 4-Way, you can use the Hopkins # HM40975 for a plug-and-play upgrade to a 7-Way (and 4-Way). Most models with the tow package do have the 12V circuit already active, but there are some that require the hot wire to be manually ran (you can check with your Jeep dealer to be sure). If this is the case you can use the Wiring Kit # 5506.

Answer 1

On the 2015 Jeep Wrangler Unlimited the brake switch wire should be a white wire with a brown stripe. Use a circuit tester such as #PTW2993 to test the wire to make sure it is the one that only has power when the brake pedal is pressed.

view full answer...

Answer 2

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Answer 3

Yes, there is a trailer brake controller plug on a 2023 Jeep Grand Cherokee WL. In order to utilize this you'll need a trailer brake controller like the Tekonsha BRAKE-EVN Trailer Brake Controller part #TK63VR and an adapter harness like the…

view full answer...

Answer 4

The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #DT78MR will go behind the bracket and use the factory bolts for installation. If you watch the attached installation video on a 2021 Jeep Wrangler unlimited you can…

view full answer...

Answer 5

Hi Ken, Starting with the wiring harness, I can verify for you the correct fit for the 2018 Jeep Wrangler Unlimited without a tow package is indeed the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118786. Then for the hitches, the…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2023 Jeep Wrangler Unlimited, I recommend the etrailer Hitch item #e98856. This hitch is custom fit and bolts to your Jeep with included hardware. The etrailer item #e98856 is a class III hitch with a 2"…

view full answer...

Answer 7

We spoke with my contact at Ventline and she stated that for your V2245-50 exhaust fan you can use the Replacement Fan Motor #BCD0390-00.

view full answer...

Answer 8

Yes. You're going to want to use the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #DT78MR, which is a confirmed fit on the 2021 Jeep Wrangler JL EcoDiesel. This hitch has a small footprint and attaches to the…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

How to Install a Brake Controller on a 2015 Jeep Wrangler Unlimited with Factory Tow Package

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching