Mounting Hardware for Older Yakima Fat Cat on 2002 Acura MDX Roof Rails

Question

Question:

I just acquired 2002 Acura MDX that has wider roof rails than will fit with standard Yakima fat cat 2010 version mounts...will the mounts you sell with rubber straps fit?

asked by: Kurt

0

Expert Reply:

If your 2002 Acura MDX has factory roof rails, the Replacement Mounting Hardware for Yakima FatCat # Y8860078 has been confirmed by Yakima to fit. This hardware was designed for the newer Fat Cat ski carriers, but will work with the 2010 version of the FatCat 6.

expert reply by: Kyle S

0

Answer 1

The universal MightyMount part #Y03590 is a fit for the older style of Yakima FatCat 6 that you have and can fit crossbar sizes up to 4 inches wide and 1-1/2 inches tall so it should work well for you. I don't have the year of Q8 that you have…

view full answer...

Answer 2

The replacement mounting hardware you will want for your 2010 version of the Yakima FatCat 6 #Y03088 is the Replacement Mounting Hardware for Yakima FatCat Ski and Snowboard Carrier #Y8860048. This is the replacement mount for the previous version of…

view full answer...

Answer 3

Hey Lance, I believe I've found what you're needing for your Yakima FatCat 6! It sounds like you're either describing one of the knobs that sits inside the carrier itself, or the clip at the end of the rubber strap that wraps around the…

view full answer...

Answer 4

We do indeed sell the replacement knobs you're looking for. They're available in a quantity of 4 as part #Y8860080. I know, you only needed one, but this way you'll have a few spares!

view full answer...

Answer 5

For your version of the Yakima FatCat 4 the correct replacement universal mounting hardware would be the #Y8860078. The modern hardware would not work.

view full answer...

Answer 6

The correct replacement mounting hardware for your Yakima ButtonDown 6 Ski Carrier is the part #8830021. This is a direct replacement and will allow your carrier to fit round or square crossbars. If you want to be able to use the carrier on wider…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Mounting Hardware for Older Yakima Fat Cat on 2002 Acura MDX Roof Rails

Product Page this Question was Asked From

Continue Researching